Question about Surveillance Cameras

1 Answer

Red light on surge protector

Is the red light supposed to stay on constantly on my surge protector along with the green "grounded" light?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 40 Answers

Yes i think it is, I think the red light just means that it is surge protected, My ones red light is on constantly to.

Posted on Sep 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Bunker hill security system. One of the camera's wires got broken. Coming out of the camera are a red, yellow & black wire. The part that hooks into deck has a red, green and bare wire. Which are...


On the camera, red is supply, yellow is video and black is common. Trace your wires back to your connection box to find out whaich one is which.

Jul 13, 2014 | Surveillance Cameras

1 Answer

3 wires red black and green what goes were


Red is +
Black is possible -
I would try it make sure its DC power. You can test it on the panel find a 12vdc terminal and a ground terminal and just touch it and see if it works.

Mar 13, 2014 | Honeywell 747 Alarm Siren

1 Answer

Red light blinking green light steady on


THIS IS A NORMAL THING FOR UNIT TO DO
GREEN IS POWER APPLIED
AND RED IS HARDDRIVE RECORDING VIDEO DOWN

Mar 07, 2014 | Lorex LH118501C4 8 Channel 500 GB DVR with...

1 Answer

Pyle plcm7300bt what does the green wire reverse car wire connect to + or ground


The green wire connects to the backup lights control. When the gear shift is in "Reverse" this acts as the switch on the "Monitor" and turns the system on so you can see what's behind you to safely "Backup" Hope this helps you.

Jan 09, 2012 | Pyle PLCM7300BT 7"TFT Mirror Monitor W/...

1 Answer

The manual says wire black to black and white to white and ground to green screw. The box i am wiring into has a white a black a ground and a red. What do I do with the red wire?


Depending on where box is and who wired it the red wire very well may be switched from inside. If you want to use the dusk on and off and sensor exclusively, in other words, you don't want it switched, cap off the red wire and don't use it. If you would like it switched, see if you can find a switch that will operate the red wire, probably somewhere around the nearest doorway out, or if you have a switch that you could never figure out what it was for.

Apr 30, 2011 | Heath Zenith All Metal Motion Sensor Light...

3 Answers

It showes me on the xls60e fire panel ardesseble


An "earth fault" or ground fault is a condition where one of your circuits is grounded or shorted to earth. While all fire alarm systems are normally grounded for circuit board overload protection and personal safety issues, all circuits (bell circuit, smoke detector/heat detector/pull station circuits) should be free of earth grounds. I would suggest if you are not knowledgeable enough to troubleshoot your system you should contact a security/fire alarm installation company to fix the problem. If this is not a viable solution and you want to attempt this on your own try removing each circuit from the panel one at a time. While this will certainly cause additional system troubles, when you remove the circuit causing the earth fault the condition will disappear. You will then need to check all wiring, spice points and devices on that circuit to determine the faulted location.

Feb 03, 2010 | Honeywell Surveillance Cameras

3 Answers

Genie excelerator light won't turn off...


First unwire the wall button. If the light will go off now replace the wall button. If not then you will need to replace the logic board on this unit(genie.com for replacement). Protect this with a surge protector as well 900 joules or higher. Thanks BB

Jan 21, 2010 | Genie Company Genie PowerLift Excelerator...

1 Answer

Security Camera


it is important to know model and make or camera if you want a solution

Jul 09, 2009 | Surveillance Cameras

3 Answers

Heath-zenith sl-6107 wiring diagram


hi there the wirings colour codes for nz are as follows

OLD WIRING CODE

Green = Earth
Black = Neutral
Red = Phase Or Live

NEW WIRING CODE

Green/Yellow = Earth
Blue = Neutral
Brown = Phase or Live

============DANGER 230VOLT ===============

Electricity can kill.
You should use an Electrical contractor for this repair job,
Caution always turn off power first before touching any wiring,

The Live wires always carry power,from one point to another,
the black neutral is your return path from the live phase wire
the green wire is always the ground ,

In this example

the sensor will have four wires as follows

Green = Earth Wire
Black = Neutral
Brown = Phase (incoming supply) 24 hrs
Red = Phase Load (outgoing supply) from sensor to lights triggered

Notice there are to phases in the circuit.Brown and Red
Always treat them as LIVE or Active Power.

Brown will normally be the Live incoming power and
Red will be the load side of the sensor,

Check the brochure supplied by manufactuers or their website to confirm the wiring order is correct before commencing any installs or repairs,

Always Safety first.
Safe a live today and you'll remembered forever.



Jul 06, 2009 | Heath Zenith Occupancy Motion Sensor Wall...

Not finding what you are looking for?
Surveillance Cameras Logo

Related Topics:

3,079 people viewed this question

Ask a Question

Usually answered in minutes!

Top Surveillance Cameras Experts

Brad Brown

Level 3 Expert

13569 Answers

kakima

Level 3 Expert

96683 Answers

Will Halftowaite

Level 3 Expert

503 Answers

Are you a Surveillance Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...