Question about Computers & Internet

1 Answer

Cisco 1750 not showing anything in cli in hyperterm

Hi,
my cisco 1750 power up with/without wic cards and no red or amber leds.
it shows power led as green stable and OK led as green and blinking, but am not able to hyperterm into it. The cli is not getting shown at all. I've tried replacing console cable as well as pc and a laptop to use hyperterm.
pls/ suggest how can i reset the same, if theres any error and get into cli.
i've tried pressing ctrl brk n all but nothing is shown in cli.

prakhara@gmail.com - 919928034007

Posted by on

  • prakhara Sep 28, 2008

    thx i've tried the solution but the OK led on the router keeps on blinking green. Pls. suggest anything else.



    thx

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 114 Answers

First, make sure your terminal settings are correct.  Also, make sure you are using the right cable.  Cisco provides a flat, blue console cable with every router and switch.
Cisco lists the necessary terminal settings for most of their models here: http://www.cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a008010ff7a.shtml
Power off the router and then power it back on.
If you are still not seeing any characters through your terminal application, then the router is most likely dead and will need to be replaced.

Posted on Sep 18, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pride Jazzy 1103 Ultra controller code: when the "on" button is pushed and held down, three red, four amber, and one green LED come on and are solid (not flashing), and there is a second LED gauge...


Seven blinking LED's indicate a "Joystick Fault" on the controllers Pride uses. Could be just the actual joystick itself, the part you move to make the chair move, or it could be other electronics in the controller. Here's a link to troubleshooting info:

Pride Mobility Products Corp Basic Troubleshooting Instructions

Dec 21, 2014 | Pride Health & Beauty

1 Answer

ML350 G3 S/board CPU Error Amber LeD + Internal Health Error


You will continue to get internal error until you add memory. It shouldn't even boot without RAM.

Feb 04, 2013 | HP ProLiant ML370 G4 Server

1 Answer

Hi, I've APC UPS ES 500 connected to my desktop computer. Have 1 year old battery but when checked without load displaying 12 V. Issues are: a. ups doesn't supply...


A battery showing 12V without a load attached means nothing. You probably have one or more weak cells and they simply cannot supply enough power. I would try a new battery before I try anything else.

Jul 21, 2011 | Office Equipment & Supplies

1 Answer

Hello! I have a dell optiplex gx260 pc i am having a problem that my pc does not boot it does not show any screen nor any beep its backlight light orders are A OFF B Yellow C OFF D OFF i have...


If the power LED is flashing amber, there may be an issue with the power supply, if it is solid amber then the motherboard itself (or if it has an expansion card in a slot, maybe the card)

Jun 08, 2011 | Dell OptiPlex GX260 PC Desktop

1 Answer

Hi, My SONY CPD G420 monitor has suddenly stopped working - the front led is blinking amber. After power cycling the LED stays green for a few seconds before going back to blinking amber. I have verified...


just unplug the signal cable and see if it shows a warning! if it shows then the monitor is in some working condition! this problem mainly is not the monitors problem its the systems problem, it seem as if the system is in standby when u on it right??? it happens when the processor doesn't get supply or it refuses to come on! you will see that the red hdd load led will not light when u start the CPU; just open the CPU and unplug the smps from the board and blow the pins to clean them up and re-fix it and see it will work. if still it doesn't work try some other smps it will work! reply and revert back for more help with a vote!

Jul 24, 2010 | Sony CPD G420 19" CRT Monitor

1 Answer

Organe color showing in Active + status led on Cisco ASA 5515


Hi the documentation lists it in detail if you donot have the docs then access the same on Cisco web site it is free

Feb 24, 2009 | Cisco ASA 5505 Firewall

1 Answer

Internal led of ML350 server is glowing.......how do i resolve it?


Hi Franceso, plz specify
Is it powering ON ?
Which LED is glowing?
These leds are there on the front panel :

1 Power On/Standby button
2 System power LED
Green = Power on
Amber = System shut down, but power still applied
Off = No power

3 Internal health LED (Wave sign in BOX)
Green = Normal
Amber = System degraded. To identify the component in a degraded state, refer to system board LEDs.
Red = System critical. To identify the component in a critical state, refer to system board LEDs.
Off = Normal (when in standby mode)

4 External health LED (power supply)
Green = Normal
Amber = Power redundancy failure
Red = Critical power supply failure
5 NIC 1 activity LED Green = Network link
Flashing = Network link and activity
Off = No link to network.
6 UID LED Blue = Activated
Flashing = System remotely managed
Off = Deactivated
7 UID button

If it is Internal health led then any internal h/w issue is suspected.
If it is external health led then any power supply or power source related issue is suspected.
Also check the status of the server & its IML (Integrated Management Logs) in ilo (Integrated Lights Out ) if it is configured. (2nd RJ45 port in rear)

Also make sure the cabinet is properly closed.

Nov 18, 2008 | HP Compaq ProLiant ML350 G3 Server

1 Answer

Cisco 2950 series


Go here http://www.cisco.com/en/US/products/hw/switches/ps628/ They have a wide range of ideas about this product. More than likely built it.?

Aug 29, 2007 | Cisco (WIC-1AM=) Modem

Not finding what you are looking for?

Open Questions:

Computers & Internet Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...