Question about Washing Machines

2 Answers

Washing machine stops before rinse cycle

This washing machine is 11 years old. Recently it started stopping right after the wash cycle. I was able to move the dial and eventually try enough things to complete the cycle - but now that isn't working anymore

Posted by on

  • geocat Sep 16, 2008

    Keep in mind that the washer will start, fill up, wash - but then stops and I have to fiddle with moving the dial to somewhere where it eventually will complete a cycle.

    The model number is KAWS77EQ0

  • geocat Sep 16, 2008

    I mistyped the model number - it is kaws777eq0. I went online at kitchenaid and was able to download the manual and it does mention replacing fuse if washer stops - so a diagram of the fuses would be helpful.





×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,543 Answers

You may have a bad or blocked water inlet valve. The wash water would fill hot water on hot or warm settings, but the rinse, being only cold, is not filling. Check the inlet water screen inside where the hose normally attaches to the machine. Also, check that there is not a screened washer in either end of the cold water supply hose that may be blocked.

Posted on Sep 16, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,689 Answers

Have you checked on the machine internally if you have a borken fuse near the control board of the washer? many times, of age, this part can be rusted and damaged, thuis needs replacement on some parts, and cleaning on most part.

what is the exact model of your wahser, so that we will be able to provide a diagram on where you may check the issue.

Posted on Sep 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Couple of years old . not old. Recently stopped completing cycles. seems to happen after the washcycle or rince, not sure. Need to manually turn over to spin and re-start machine. help!!


Be certain BOTH fill hoses are turned on. What happens is hoses get reversed, and someone turns off the hot water (which is connected to the cold inlet) and the machine needs cold water on rinse, so it will JUST STOP and wait happily forever. Both taps on and then check for reversed hoses.

Mar 31, 2011 | Washing Machines

1 Answer

My machine has recently started not completing a full wash cycle and seems to stop before the rinse and spin completion. It also shows a "nf" in the digital readout. any ideas?? Of course I cannot find...


Look carefully at supply water. sometimes hoses are reversed, dad wants to save money and turns off hot, but water is needed to finish rinse cycle....turn on both taps and test again.

Sep 06, 2010 | Maytag Washing Machines

1 Answer

Kenmore washer - water won't drain. It stops


If the water drains between the wash and rinse cycles, your motor and pump are probably OK. If this is a machine with a dial, try a different cycle, like normal instead of heavy duty. If that works and the machine completes the entire cycle then the timer probably has a bad spot. You might try to find a replacement timer if that is the case although I didn't have any luck with my 10 year old washing machine. Best of luck

Mar 20, 2010 | Washing Machines

1 Answer

Nec nw-891 washing machine will not complete the programmed cycle


Apparent malfunction in the timer circuits. Specific Component replacement not available.

Jun 30, 2009 | Washing Machines

1 Answer

Maytag commercial washer gets to spin cycle and stops


It sounds like your timer is defective

FIX

When the machine gets to the rinse cycle slowly advance the setting to manually advance the timer
if it just sits bang on the panel or around the knob and listen if ou hear the timer start ticking you will need to replace it

Timers are avaliable from appliance parts suppliers around $29 you can get someone to install it or if you are handy can do it yourself

good luck

Nov 18, 2008 | Roper RAS6233KQ Top Load Washer

2 Answers

Hoover 550 MA Top Loading Washing Machine


if if spins the belt is ok,may have timer fault or timer module ( next to timer) if fitted will be faulty

Mar 24, 2008 | Washing Machines

1 Answer

GE Nautilus won't drain after Rinse Cycle


Check disposer plug. If a garbage disposer has been recently installed, it is possible the disposer drain plug was not removed. The drain plug is a plastic piece in the disposer that blocks the hole where the dishwasher hose connects. Also check the hose connected to the disposal. Mine apparently had a kink in it. When I straightened the hose the dishwasher drained at full speed (I recently had a plumber re-route a hot waterline. He must has bent the hose). Hope this helps. If not go to the GE website. That's where I found my answer.

Nov 03, 2007 | GE 25 in. Nautilus GSC3400J Free-standing...

1 Answer

Beeping and odd light sequence


I have the same problem with my 603 washing machine stopping in the middle of a cycle and i would have to go and manually advance the wash. I have just replaced the top curcuit board with a new one. can you please help or offer a solution. Thank you.

Jun 14, 2007 | Fisher and Paykel GWL11 Top Load Washer

2 Answers

Bosch Axxis front loader will not drain


check filter. check no foreign objects fouling pump impellor - bra wires are the favourite

Apr 25, 2007 | Bosch Axxis WFL 2060 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

Brad Brown

Level 3 Expert

15133 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...