Question about Projection Televisions

Open Question

Sceptre s1701dtv need parts - Projection Televisions

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sceptre X405BV FHD3FET will not startup sometimes.


Fault to the main power supply regulator section. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/
It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.

Jun 19, 2016 | Projection Televisions

2 Answers

Part needed


Send me the part # you need then I can tell you. I just repaired same set.
jmk2938@gmail.com

Dec 12, 2009 | Hitachi 57F500 57" Rear Projection...

1 Answer

Mitsubishi TV M# MS55513


not sure which part you need main board (where flyback lives) is part no. 930b903002, power board ( where convergence IC's live) is part number 930b904001, signal board ( where tuner lives) is part no. 930b905001-55. I checked with encompass.com they have all three in stock.

Aug 23, 2009 | Projection Televisions

1 Answer

I need part #31350170601 for model #43p8341 philips 43" tv


Apparently the original part you need is obsolete. Through a lot of research, I've found a substitute at www.partstore.com They list this part as a PCB keyboard and list your model television as a match for this part. Here is the direct link to the part. They also have a toll free phone number if you want to discuss the part b/4 you buy. 1-866-925-PART (7278) Best of luck to you on your repair!

http://www.partstore.com/Part/Royal+Philips+Electronics/Philips/313503710441/New.aspx

May 03, 2009 | Philips 43P8341 43" Rear Projection...

2 Answers

Philips dlp fan replacement


Try here.

If they do not have the part in list call them at 1-866-925-PART (7278)and they will find it.

Partstore is the biggest part distributor worldwide.

Sep 17, 2008 | Projection Televisions

1 Answer

Need part number????


The Hitachi part number is: 2338313 and is available for $3.22 from tritronicsinc.com

Hope this helps,
Dan

Aug 26, 2008 | Hitachi 53SBX59B 53" Rear Projection...

1 Answer

Mitsubishi 55in. Big Screen TV


You have the wrong part number you need part number 334P278010 for the WS55859 flyback. If mitsubishi doesnt have one let me know and I will post a link where you can get one.

Jul 04, 2008 | Projection Televisions

1 Answer

NEED TO BUY A PARTS FOR THE PROJCTOR ON SONY KDF42 655


Exactly what part are you looking for as thats not a valid sony part number. Is KDF-42WE655 the correct model number of your set? If so let me know and explain what part youre needing and I can post a link to where you can get the proper part for your model.

Jun 10, 2008 | Sony Grand WEGA KDF-42WE655 42" Rear...

1 Answer

PARTS NUMBERS


What parts are you needing and I can help you locate the part numbers as well as where to buy them.

Jun 07, 2008 | Philips 51PW9303 51" Rear Projection...

1 Answer

Lcd television trips circuit breaker when plugged in to wall outlet. Problem started yesterday after wall mounting the unit.. Removed wall mount and it still happens (worked fine before wall mounting...


I would check 2 things. If the TV trips another breaker in the house of the same rating, you probably have a short in your TV and will need to have it serviced.(You didn't drop it did you? :-) ) The short may also occur by too much stress on the power cord where it enters the TV, common to need to cram the cord into small spaces when wall mounting. If the TV only trips that particular breaker, I would try replacing the breaker. Replacing the breaker costs very little and will only take you a few minutes. You can buy a replacement breaker at most hardware stores. Just make sure to disconnect the main supply first! Also, make sure the breaker is rated correctly, using a higher amperage breaker will increase your chances of starting a fire.

May 05, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...