Question about Homedics 10 Motor Back Massager with Heat

1 Answer

Homedics programmable percussion massager with heat

Our massager abruptly stopped working. We can hear the faint hum of the motor, but the touch pad will not engage. Is there a solution for this problem?

Barbara Jersey
120 Tall Oak Drive
Hainesville, Il 60073
1.847.548.5357
urbaneagles@comcast.net

Posted by on

  • christian walker
    christian walker Dec 18, 2013

    if the motors are huming and try taping them lightly or to by pass the switch take the wires to the swith and tap them together

  • Anonymous Mar 24, 2014

    MaSSAGER WONT STAY SWITCHED ON

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 505 Answers

The motor is Jammed
Try Taping it or banging it lightly
if that don't work im sorry ether needs repair or buy a new one

Regards; Aaron

Posted on Sep 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WTW 4800XQ1 not working. Start lite goes on, fill lite goes on, then start lite goes off.


Hello. When you press the start button, you should hear the lid lock engage, then disengage after a short pause, then re-engage. If this doesn't happen, the lid lock might be defective, (the locking, unlocking, then re-locking is a self test). The motor should make some short, slow spins to determine load size. Listen for the motor--if all you hear is a "pulsing faint humming or buzzing noise", there is a part failure causing the motor to not move correctly. Because of the electronic design, you will have to call for service to determine the failure cause.

Aug 19, 2015 | Whirlpool Washing Machines

1 Answer

I was given a homedics percussion action handheld massager with heat. It won't work at all. It does nothing!


Check that you have power and that there is a lit LED when a massage attachement is put into the top. Otherwise check this link for further instructions and power issues.
The 3 Best Handheld Percussion Back Massagers Under 50 Back Pain Relief...

http://back-pain-relief-products.net/handheld-percussion-back-massagers/

Feb 09, 2015 | Homedics Health & Beauty

1 Answer

Rocker arm hums does not cycle


Do you mean that it is the motor that is "humming", and you sense vibration in the pads? Perhaps it's only from dirty contacts on the switch (which can be cleaned easily). Otherwise, it means that the motor is either broken or not being allowed to function due to breakage of one of the links in the system. For that, you'll have to open the case & check.

Feb 02, 2014 | Thumper Mini Pro 2 Massager

1 Answer

Grinds when the car has been stalled for a bit and then started. Sounds like a metal scraping noise. Also when decelerating or reaching a stop it whines and towards the end if broken abruptly it does


The grinding noise when you are braking is worn out pads. Metal against metal is not good for your discs - replace the pads otherwise your up for machining of the discs or replacing. That noise on start-up is common with worn teeth on the fly wheel. The fly wheel will stop in "common" positions just how the momentum of the motor works and the teeth can wear out at these spots - sounds horrid but is not "unsafe" problem is one day you may not be able to start the car if the starter cannot engage the fly wheel to turn the motor over. This is where you hear of people turning the motor over a little by hand (they usually remove the stone plate from below the fly wheel to hand crank the engine) I don't recommend this practice probably better to price a replacement and while it is apart consider any other work eg. Clutch or minor seal leaks as it is not a small job to replace the flywheel.

Jan 18, 2013 | Cars & Trucks

1 Answer

Which heads to use for what


The Manual says the heads are color coded:
Black = Soft Massage
Medium Grey = Medium Hard Massage
Light Grey = Hard Massage
Red = Heat Massage

Jun 13, 2011 | Homedics Pa 100h Percussion Massager With

1 Answer

Calf and foot massager does not go up and down. Switch clicks, motor hums, piston does not move. What do you think? Thanks, Brian Shore 315-956-2065


It sounds like the piston assemby might be jammed. The motor will hum since it's trying to run, but will just buzz if the output isn't turning. Otherwise, it could be a broken part in the piston assembly. You will have to partially disassemble the chair to see what's going on. If it's under warranty, contact Human Touch. The same for replacement parts.
Good luck, and hope this helps.

Jan 31, 2011 | Human Touch HT 7120 STRETCHING Home...

2 Answers

I'm having a problem with my Homedics SBM 300H Massager. I was using it when it suddenly stopped, after hearing a faint "pop" sound from it. I tried re-plugging it in another outlet but still no...


Yes there was a short circuit and am sure the massager and the cpomputer where plugged in the sane extension box that was why there was loss of power when the massager stopped working.For the massager it is the fuse so get a new fuse for it.

Jan 21, 2011 | Homedics SBM 300H Therapist Select Shiatsu...

1 Answer

MY WASHER FILLS WASHES, BUT WONT DRAIN OR SPIN, AND I DONT HEAR A HUMMING NOISE


As you mention not hearing a humming noise usually means there is no power to the motor assembly. A very common cause of this is a defective lid switch.

Open the machines lid or door press the striker pad and listen for a clicking sound. Or open and close the lid/door gently listening for the same sound, the switch to engage.

You'll probably find thats your problem.

Take care

Nov 23, 2010 | Whirlpool Washing Machines

Not finding what you are looking for?
Homedics 10 Motor Back Massager with Heat Logo

Related Topics:

723 people viewed this question

Ask a Question

Usually answered in minutes!

Top Homedics Health & Beauty Experts

Cindy Wells

Level 3 Expert

4882 Answers

Ankit Chandel
Ankit Chandel

Level 2 Expert

127 Answers

Are you a Homedics Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...