Question about Neff Ovens

Open Question

Oven timer volume

Is there any way I can increase the volume of the timer on this oven? Also, it stops beeping after a couple of minutes, which makes it useless unless you are in the kitchen the whole time. Is there a way to overide this too?

Posted by on

6 Suggested Answers

melnavz
  • 1226 Answers

SOURCE: smeg electric oven timer controls

Hello,

first is unplug the the oven from the wall outlet, to hard reset the setting. wait for almost 20 minutes then plug it again.

please tell me if there is still problem after this, melnavz

Posted on Apr 10, 2008

  • 1073 Answers

SOURCE: Whirlpool Oven/Convection Oven Timer Problem

replace the control cpu unit the main control board is deffective

Posted on Apr 11, 2008

  • 3 Answers

SOURCE: I have a kleenmaid TO 551X wall oven and i was

Hi, Did yo work out your problem? When your oven beaps, press the - ot + on the oven, should change the volume.

Posted on Mar 30, 2010

  • 1 Answer

SOURCE: oven timer goes off when not being used

I have the same problem with the beeping and screen flashing F1 does anyone have a solution yet?!

Posted on Jun 27, 2010

  • 1 Answer

SOURCE: volume control candy oven timer

Switch off the oven, leave for 5 seconds and switch it back on.
Candy Customer Services asked for over £100 to have an engineer sent to my house, which I refuse as I thought the oiven was good.
I had to switch off all the electricity in the kitchen but after this 'reset' the oven turned to the normal 'high' volume.

Posted on Aug 03, 2010

blueextc3221
  • 15935 Answers

SOURCE: Kenmore Oven model 790-30179400 code F11

Here is some wisdom for understanding F1 fault codes.

In some models, there are subcodes that make diagnosis even easier.

Here's a simple explanation of what's going on and how to troubleshoot:

The F1 code indicates that:


a. The electronic range control (ERC) is sensing heat in the oven when in a time-of-day (i.e., not cooking) mode.

b. The ERC is receiving information to run multiple heat functions simultaneously.


Although different components (depending upon the model) could generate the code, simple and straightforward testing using your ohm meter is all you gotta do to test for it.

1. Check the oven temperature sensor. The oven sensor has to be within spec or it will cause the F1 code.
As an example of being out-of-spec, the ERC will generate an F1 fault code when the sensor shows 1650 ohms during a time-of-day mode.
This is equivalent to 350°F in the oven.
The resistance isn't high enough to generate an F2 code (runaway temp) or an F3 or F4 code (shorted/open sensor circuit).
The ERC monitors the sensor circuit after a heat cycle and expects the resistance to drop back to 1050-1100 ohms.
The fault code is generated when this doesn't happen. Checking the sensor circuit means also checking the harness,
harness connections and the sensor itself.

2. If the oven sensor circuit checks okay, then turn your inquisitive eyeballs to the touchpad.
If the range has a separate touchpad/keyboard, the keypad may have moisture that is shorting several circuits simultaneously.
If the F1 code is given immediately (instead of during or after a heat cycle),
remove the ribbon connector from the touchpad to the ERC after clearing the F1 code. If the F1 code does not return in five minutes,
then cast a suspicious gaze upon the touchpad/keyboard. Shorts may be caused by using an ammonia-based glass cleaner.
The touchpad surface will absorb ammonia-based cleaners that are sprayed directly on the glass surface. When heat is applied,
the surface material can break down causing shorts.
If you're gonna use ammonia-based cleaners on your control panel, then you should spray it on the rag and then wipe the touchpanel
-don't spray directly onto the surface of the touchpad.

3. On Amana ranges with a rotary temperature dial, be sure that the knob is in the OFF position when performing tests.

4. If these tests all check good, then replace the ERC.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
**$^

Posted on Sep 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timer volume too low


some units can be adjusted for louder tone volumes,depending on your model you can check the user manual supplied with the oven to find out if volume increase is possible or go to maytags web site and you can download a user manual or ask them online if its also possible to do this with your model

Nov 29, 2012 | Maytag Ovens

1 Answer

I have a Hotpoint Double oven DQ471/2. The timer bleep is so quiet I cannot hear it and my partner who has a hearing difficulty finds it impossible. Our old New World oven had a bleep which was...


unfortunately there is no way of increasing volume of the bleep. its basically a simple beeper on the timer with no way of adjusting.
sorry cant be of much more help but what i will say is you should contact hotpoint about this problem as obviously is a design flaw.

Mar 18, 2011 | Hotpoint Ovens

1 Answer

Timer won't stop beeping every minute on the minute ALL NIGHT LONG and oven won't turn off. Turned off gas, unplugged and it beeped ALL NIGHT.


good job on trurning gas off and unpluging machine. Possible problems...... control boad relay bad, Thermostat bad, Gas valve bad,


I strongly suggest you have a pro look at your machine.

Sep 08, 2010 | Ovens

1 Answer

Hotpoint Openspace Timer problem


no, but can i ask your general opinion of this as thinking of buying one

Apr 07, 2010 | Ovens

2 Answers

Volume on timer really quiet hotpoint forno


Pressing the "-" button on the control panel will cycle through the 3 or 4 available beep tones / volumes. No need to press any other buttons during or before this process.

Shame Hotpoint didn't see fit to put this in the manual. We dicovered it by mistake!

Jul 29, 2009 | Hotpoint UY46 Style Line Stainless Steel...

1 Answer

Cook timer keeps chiming


it starts chiming every min AFTER the timer counts down the allotted time?? thats normal operation its remonding you that the timer has completed cookin and to remove food from oven.. it will continue cooking with residual heat if not removed

Nov 25, 2008 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

Oven timer goes off when not being used


I have the same problem with the beeping and screen flashing F1 does anyone have a solution yet?!

Aug 22, 2006 | Magic Chef 9512 Electric Single Oven

Not finding what you are looking for?
Ovens Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Neff Ovens Experts

bosch5

Level 2 Expert

157 Answers

paulcarew

Level 3 Expert

1915 Answers

xxxxxx xxx

Level 3 Expert

4706 Answers

Are you a Neff Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...