Question about Canon PIXMA MP130 All-In-One InkJet Printer

3 Answers

Error (5800) My Cannon PXIMA MP130 kept showing the message "Check Printer Error (5800)" even after I have cleaned the waste ink reservoir on the right side of the printer. Suggestions given for the same problem on MP150 model did not work. Help me solve the problem as we have no cannon service center in Myanmar for printers. Percy

Posted by on

  • 1 more comment 
  • nulao36 Sep 18, 2008







    Post to this thread Post a new message thread






    canon mp130 (error 5800) by mark a (9/20/06 1:38 AM) reply
    + / -


    printert comes up with error code 5800 before intialising can anybody help please








    Re: canon mp130 (error 5800) by arifinsukardi (9/20/06 1:59 AM) reply
    + / -


    Mark, you can try this:

    Turn on the printer (MP130) and do the following:
    1. Press MENU SCAN COPY SCAN to enter service mode
    2. Use > to go to NVRAM ACCESS
    3. Set ABS-M LEVEL to 0
    4. Set ABS-P LEVEL to 0
    5. Press STOP to exit

    Done, hope it work.
    I tried this suggestion by Mark and it work!!! Your suggestion did not work.

  • nulao36 Sep 18, 2008

    I posted that solution that worked on my printer. I found it on other site. I hope others will also be as successful as I am.

    Percy

  • Anonymous Apr 18, 2009

    Thank you all... :) it;s works! :)

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Waste ink is full counter reset.

Posted on Sep 18, 2008

  • giuseppe caiazzo Sep 18, 2008

    1) Enter SERVICE MODE By pressing Menu-Scan-Copy-Scan
    2) Enter NVRAM by presing <--- or ---> then OK
    3)SET ABS-M LEVEL TO 0
    4)OK

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thank i solve my problem Error 5800

Posted on Nov 06, 2008

Thanks it work

Posted on Oct 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Canon mp130 shows error "


To reset waste ink counter:
Press Menu-Scan-Copy-Scan to enter service menu.
Use arrow keys to scroll to "Service menu counter access".
Press OK.
Use arrow keys to scroll to "ABS-M DOT COUNT"
Press Copy.
Use arrow keys to reset count to zero.
Press OK.
Press Stop/Reset.


OR


Reset for mp130
turn on the printer press menu
press scan, copy, scan to enter service mode
use> to get to nvram
set ABS-M level to 0
Set ABS-P level to 0
Press stop to exit..........Done

i hope this help

Jan 26, 2011 | Canon PIXMA MP130 All-In-One InkJet...

Tip

"The waste ink absorber is almost full" message?


This applies to the CANON PIXMA MP130 and other ink-jets made by Canon/Pixma.

According to the user's manual, "Ink used to clean the print head is absorbed by the waste ink tank. When this message is displayed, the waste ink tank needs to be replaced, or the machine requires maintenance". There is no information about how to replace or empty the waste ink tank.

In any case, you can try the following to clear up the error, but eventually you'll need the waste tank to be emptied or replaced. And as far as I know, you can't find the replacement parts to buy, nor the instructions to empty the waste tank.

Turn on your MP130.
1) After that press: Menu - Scan - Copy - Scan or Menu-Copy-Scan-Copy-Copy in some models, it depends on the date it was produced)
2) Select TEST MODE.
3) Enter NVRAM ACCESS
4) Select SET ABS-M LEVEL TO 0
5) Select OK
6) Keep selecting OK untill you leave the TEST MODE

Then turn it OFF and again ON. Check if the error message is still there.
The following is taken from the Canon website, regarding this specific error:

"Canon recommends having the printer serviced before the absorber becomes full. We are aware that there are many "do-it-yourself" Web sites that offer instructions for making this repair. Replacing the ink absorber is a complicated and potentially messy procedure. Even if the ink absorber is successfully changed, the ink absorber counter must be reset. Be aware that if you attempt this procedure, it is at your own risk."

As I mentioned before, I have not found any way or procedure to empty or replace the waste ink absorber nor the necesary replacement part.

on Apr 02, 2010 | Office Equipment & Supplies

1 Answer

I HAVE A CANNON PIXMA MP170 AND IT KEEPS SHOWING THE MESSAGE WASTE INK FULL & CODE 5800 ... BUT I NEED TO USE THE PRINTER URGENTLY... PLEASE ADVISE.... MANY THANKS..


Hi:
The problem here is the waste ink pads are full, these pads are located at the lock posistion to the far right where the units cartridge holder goes when you power down the unit and on start up. The way to solve this to to have the pads replaced, they are used to collect the waste ink the printer uses to clean itself when starting up, These pads usually take a long time to fill up, so either you do alot of printing or you hve used Non Canon inks or generic refill cartridges in the past, these are not good for your printer as some of these types of inks are either to thin or to thick and fill the pads up prematurely..Keep in mind to always use recommended guine ink cartridges you may save a little now with ink refill cartridges but in the long run your printer will eventually give out.

Jul 14, 2010 | Office Equipment & Supplies

1 Answer

I keep getting this error message come up, 'The waste ink absorber is almost full - see manual'.what do I need to do as the manual doesnt give details.


According to the user's manual, "Ink used to clean the print head is absorbed by the waste ink tank. When this message is displayed, the waste ink tank needs to be replaced, or the machine requires maintenance". There is no information about how to replace or empty the waste ink tank.

In any case, you can try the following to clear upo the error, but eventually you'll need the waste tank to be emptied or replaced.

Turn on your MP130.
1) After that press: Menu - Scan - Copy - Scan or Menu-Copy-Scan-Copy-Copy in some models, it depends on the date it was produced)
2) Select TEST MODE.
3) Enter NVRAM ACCESS
4) Select SET ABS-M LEVEL TO 0
5) Select OK
6) Keep selecting OK untill you leave the TEST MODE
Then turn it OFF and again ON. Check if the error message is still there

The following is taken from the Canon website, regarding this specific error:
"Canon recommends having the printer serviced before the absorber becomes full. We are aware that there are many "do-it-yourself" Web sites that offer instructions for making this repair. Replacing the ink absorber is a complicated and potentially messy procedure. Even if the ink absorber is successfully changed, the ink absorber counter must be reset. Be aware that if you attempt this procedure, it is at your own risk."
As I mentioned before, I have not found any way or procedure to replace the waste ink absorber nor the necesary replacement part

Mar 22, 2010 | Canon PIXMA MP130 All-In-One InkJet...

4 Answers

MP130 Ink waste tank is full how do I empty it


To reset the Waste Ink Counter:---------------------
  • Press Menu----------- Scan -------------- Copy----------- Scan, to enter Service menu.
  • Scroll to option " Service Menu Counter Access ".
  • Press OK.
  • After entering Scroll to " ABS-M DOT COUNT ".
  • Use arrows to reset the value to ZERO.
  • Press Stop or Reset.
Thats the Solution.
To Clean Waste Ink Pads:-----------------------------
  • Open the cover ( the cover you open to replace the catridges ).
  • Locate the Waste Ink Pads which are situated in the or under the Catridge Slider.
  • Dry up Waste Ink Pads ( You should wear Gloves when holding them).
  • Rinse the pads with Alcohol and make them dry.
  • Replace Pads .Then Set them. Make sure they are sitted properly.
Thank you Sir, I hope I helped you. Have a nice day.

Sep 21, 2009 | Canon PIXMA MP130 All-In-One InkJet...

1 Answer

I am getting an 5800 error


Ink Absorber Replacement OptionsThis printer has an ink absorber that takes in ink during the printing and print head cleaning processes. The cleaning process is necessary in order to keep the print head nozzles from becoming clogged. Over the life of the printer, the amount of ink that the ink absorber has absorbed is calculated by the printer. Eventually, after substantial use, the printer will enter an error condition when the ink absorber is nearly full. At this point, printing is still possible. Press the <OK> button to release the error. You will still be able to print for a short period. To protect the printer from damage, you will not be able to print at all once the ink absorber is full.
Canon recommends having the printer serviced before the absorber becomes full. We are aware that there are many "do-it-yourself" Web sites that offer instructions for making this repair. Replacing the ink absorber is a complicated and potentially messy procedure. Even if the ink absorber is successfully changed, the ink absorber counter must be reset. Be aware that if you attempt this procedure, it is at your own risk
the 5800 code. uplug cord from outlet. wait 1 full min, then plug in and let go through self test.
reply for more help.
have a great day and please rate bama46, thank you

Aug 17, 2009 | Canon PIXMA MP130 All-In-One InkJet...

2 Answers

Cannon printer, model PIXMA MP130/110, waste ink absorber is full


cannon printer pixma mp130/110 waste ink absorber is almost full how do i fix it

Jul 05, 2009 | Cannon Office Equipment & Supplies

2 Answers

Error code 5800 for Pixma MP130. When try to get


you can try this:

Turn on the printer (MP130) and do the following:
1. Press MENU SCAN COPY SCAN to enter service mode
2. Use > to go to NVRAM ACCESS
3. Set ABS-M LEVEL to 0
4. Set ABS-P LEVEL to 0
5. Press STOP to exit

Done, hope it work.

May 30, 2009 | Canon PIXMA MP130 All-In-One InkJet...

1 Answer

Canon mp130 showing invalid key/set when pressing menu and check printer 5800 waste ink tank full how do i get printer to go


desliga o cabo de energia, segura o resset pressionado e coloca novamente o cabo de energia o menu sera desbloqueado.

Sep 30, 2008 | Canon Office Equipment & Supplies

Not finding what you are looking for?
Canon PIXMA MP130 All-In-One InkJet Printer Logo

1,215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

1812 Answers

Corne Viljoen

Level 2 Expert

385 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...