Question about Hotpoint First Edition WMA12 Front Load Washer

1 Answer

Changing drive blet

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hotpoint Master
  • 3,463 Answers

Remove top cover and lower rear panel.
Tilt m/c towards you and put belt over motor pulley and slowly force belt round drum pulley turning the pulley at the same time.
Watch your fingers, it is very tight, but persevere!!!

Posted on Dec 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you change the drive belt that runs to the motor. I can't even figure out how to get the old blet off.


first -make a diagram of the belt position
next there will be adjuster pulley/s or spring loaded pulleys to release to loosen the belt
you may have to remove cutter drive belts to assist in the replacement
get diagrams of how they are before removing them

Aug 12, 2015 | Swisher T14560 T - 60" Trailmower with 14...

2 Answers

Why would my dryer squeal?


Problems with the drum belt drive

Sep 06, 2014 | Dryers

1 Answer

Drive blet 2000 Buell M2 Cyclone


Harley Davidson or american sportbikes are two of the only places to get them.

Dec 09, 2012 | 2000 Buell M2 Cyclone

1 Answer

Drive belt diagram a3 2001


You can get the diagram from the DAYCO blet diagram booklet at the google web page by clicking here.

Jul 24, 2012 | Audi S3 Cars & Trucks

1 Answer

Fitting new drive blet


just loosen the adjuster and when it loose pull-out the loosen belt and replace with the new one and retight the adjuster at exact belt tension

Jul 13, 2012 | Craftsman 17.5 hp 42 in. Deck Lawn Tractor...

1 Answer

Just quit while driving and now won't start


U will need to check the fuel pressure, check the cam blet for breaking and run the electronic engine control codes, the cam belt should have been replaced at 60,000 miles, they do break after that mileage, are u over the mileage without the belt being changed?

Mar 19, 2010 | 2002 Kia Sportage

3 Answers

Timming belt broke is it easy to replace my self and does it effect any thing when it broke


THIS CAR USES WHAT IS CALLED AN INTERFERENCE ENGINE, THIS MEANS IF THE BElT BROKE WHILE DRIVING YOU HAVE BENT THE INTAKE AND EXHAUST VALVES, VERY REARELY THIS DOESN'T HAPPEN SO PUT A NEW BLET ON AND CHECK THE COMPRESSION, IF U HAVE NO COMPRESSION OR LOW YOU WILL NEED TO HAVE THE CYLINDER HEAD REMOVED AND THE VALVES REPLACED, U MAY ALSO HAVE BROKEN A PISTON CROWN AS WELL, THE NORMAL CHANGE INTERVAL FIOR THE TIMING BLET IS 120,000 MILES, SO IF IT BROKE BEFORE THAT CONTACT CHRYSLER THEY MAY PROVIDE SOME ASSISTANCE WITH THE REPAIR COST.

Dec 21, 2009 | 2001 Chrysler PT Cruiser

1 Answer

Clothes wet after rinse cycle


lift the washer on its side and see if it has a drive blet that broken for the spin cycle.

Sep 16, 2009 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

The drum drive pully is loose. How tight should


The blet should have 1/4" deflection (approximately) over the longest length.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Sep 04, 2009 | Kenmore Washing Machines

1 Answer

MTD reartine tiller, wheels won't turn in or out of gear


broken drive blet or chain, check accordiningly

Nov 05, 2008 | Garden

Not finding what you are looking for?
Hotpoint First Edition WMA12 Front Load Washer Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

Todd Arndt
Todd Arndt

Level 3 Expert

2044 Answers

puggy666

Level 1 Expert

47 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...