Question about JVC DR-MV5S DVD Recorder/VCR

1 Answer

Blinking light will not work at all. purple light constantly blinking

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,071 Answers

Try to hard reset the DVD unit or some DVD unit have a reset button. If available and accessible, try using the reset buttons .Leave it unplugged for 4-6 hours and then plug it again and use..If this did not help Try to contact a service centre or service person because this is probably a hardware problem which definetly needs service and replacement!!...Thank you..

Hope this helps you....

Kind Regards!!


Posted on Sep 15, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why red charge light keeps blinking?

Is your battery a LiPo (Lithium?) If so ... These special batteries are charged by a computer circuit that holds the charge amperage constant and adjust upward the charging voltage until the required battery voltage is reached. At this time the charger hold a constant voltage and decreases the amperage as the battery capacity is "topped off". the charger circuit charges the entire battery at once but monitors each cell (cells are about 3.7 volts each) and controls the charge so that all the cells are ballanced.

When one of the cells that makes up the battery starts to go bad, the ballance circuitry prevents over charging the others, so one weak cell hold all the cells back from full charge and better charger circuits will signal you with an led or such that the battery is' going' bad.

May 07, 2014 | Radio Shack Accurian LMD-5108A Portable...

1 Answer

Hello! My harmon kardon hs100 constantly blinks an amber light and is inoperatable. I tried plugging it out in fact for months I did so and still not working power light still blinking amber.

This is due to a audio output problem in the amp, first check the speaker wires for shorts, if okay! the audio output semiconductors must be replaced to remedy the situation.

Apr 06, 2012 | Harman Kardon DVD31 DVD Player

1 Answer

Why is my charge light indicator blinking instead of showing a solid orange color?

It is attempting to charge the battery, if it blinks constantly the battery is reaching a point where it can't hold a charge. To test this, unhook the power supply adapter to see long the battery lasts while you watch a movie "1.5 to 2.0 hours is the norm" anything less the battery is suspect.

Jan 12, 2011 | Initial IDM-1731 Portable DVD Player with...

1 Answer

Philips dvp3150v vcr/dvd combo "code" for universal remotes

try following codes
RCA universal remote controller:
021, 022, 062, 096, 124(VCR)
162, 356, 357(DVD)
Philips Magnavox Universal Remote PM335
130 226 330 536 631 734 738(VCR)
441 442 943(DVD)
many direct codes doesn't work ,code searching method all ways work better but irritating
1. Press and hold CODE SEARCH
lights, then release CODE
2. Press and release the device
button for the device’s code
you are retrieving (TV,VCR or
LIGHT will blink once then
remain lit.
Note: For AUX, press DVD•AUX
then the device button for the
code you are retrieving.
3. Press and release CODE
LIGHT will turn off.
4. Starting with 0 on the keypad,
press the number buttons in
order (0-9) until the
5. The number which causes the
the first digit of your code.
6. Repeat step 4 until you have
retrieved all three numbers in code

if any of the above works note down code used in small bit of paper and place it in the battery chamber(safe place)

May 09, 2010 | Philips DVDR3435V/37 DVD Recorder/VCR

1 Answer

TV will not power on

not sure but probably needs a new lamp mine went out on my jvc tv and my power light just blinked at me whether the tv was on or off

Apr 30, 2009 | Audiovox VM9311TS

1 Answer

Blinking lights

I left if off and unplugged for a few hours. When I plugged it in it started working again. My recommendation if this happens to you is to just unplug it all and let it stand for at least 4 hours and then plug it back in.

Good Luck

Oct 01, 2008 | Sony RDR-VX555

1 Answer

Blinking power light

I got the same problem too.

Jul 11, 2008 | Jwin JD-VD140 DVD Player

2 Answers

Se-d1 will not boot

escient music server...light blinking red...
cant turn on system...
tried resetting...nothing
tried turning system off..for a hour or two...nothing..
juse blinks will not respond to anything...
any ideas.

Jun 28, 2008 | Digital Products Escient SE-D1 FireBall...

Not finding what you are looking for?
JVC DR-MV5S DVD Recorder/VCR Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69795 Answers

easy alberta
easy alberta

Level 2 Expert

132 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a JVC Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides