Question about Maytag MGR5880BDS Gas Kitchen Range

1 Answer

Please help/getting code F!

Turned oven off/display panel beep once then shows f1. what do i do? what is the problem? thanks so much

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Maytag Master
  • 3,361 Answers

Replace the oven clock control.

Posted on Mar 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My F1 Code keep beeping.


I think you must post full information about your stove

Dec 06, 2013 | GE Kitchen Ranges

5 Answers

I need Please a solution to F1 Error Code on GE/Kenmore electric ovens Model # 911.4658815 Thanks E-mail: elylimo@gmail.com I have the same model number. 9114658811 and plugged in the stove for the...


Hi,

To my understanding error code F1 would indicate a faulty control board, possibly thermistor control. The only recourse is to have this replaced.

This of course would require a fair familiarity of electrical/electronic components/circuitry and safety procedures, use of a DVM and possibly a soldering iron. It would be to your added advantage access to a service manual or at the very least a schematic diagram with voltage readings. Should you be uncomfortable performing a DIY (do-it-yourself), perhaps your best bet would then be to seek the services of a qualified professional.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Oct 13, 2008 | Kenmore 46123 Stainless Steel Electric...

1 Answer

I have a mer5730aaw my bottom element dosen't work.Then the display showed F1 and started to beep.So I unplugged the oven and disconnected the multi wire to the control panel.Then it displayed F3


F1 touch pad / ERC test This simple test will help determine
whether the ERC (Electronic Range Control or Clock) or the touch pad is
defective when F1 error code is present.



Note: Some models incorporate the touch pad in to the ERC as a single
assembly, in which case this test is not necessary. Simply replace the ERC
(Clock).



Warning: If you feel in any way uncomfortable performing this test or
making this repair, please contact a qualified appliance repair technician.


1. Disconnect power to the range (unplug the range power cord or turn the power off to the range at the circuit breaker). It is very important that the power to the range has been disconnected, so please double check before continuing


2. Gain access inside the control panel.

3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC


4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was


5. Turn the power back on.

6. Wait for at least one hour to see if the F1 code comes back (usually accompanied by a beeping sound)


7. If F1 comes back, replace the ERC. If it does not, replace the touch pad.




Dec 09, 2010 | Maytag MER5530 Electric Kitchen Range

1 Answer

I have a tappan range that keeps getting F1/F3 in on the display panel.


How to test many brands of Ranges that are flashing a F1 fault code: You have either a bad ERC (clock) or a bad touch pad.
  1. Disconnect power to stove
  2. Gain access to the back of the clock (electronic range control or ERC).
  3. Unplug the touch pad ribbon connector from the ERC. This will be a flat wire approx. 1 1/2" to 2" wide.
  4. Make sure everything is clear and will not short out when power is turned back on.
  5. Turn power back on to stove.
  6. Watch for the F1 and listen for the beep.
  7. If you get the F1 and beep, replace the ERC.
  8. If after approx. 30 minutes you do NOT get the F1 and hear the beep, replace the touch pad.
    NOTE: Some models incorporate the touch pad and the clock as one part. * We have seen a few of the newer Maytag ranges with a F1 fault code and the problem was the oven temp sensor, check carefully the wires to and from the oven temp sensor!!

Mar 03, 2010 | Tappan TGF363 Gas Kitchen Range

1 Answer

Oven door locks, the panel beeps, and displays F1 error code


Here is some wisdom for understanding F1 fault codes.

In some models, there are subcodes that make diagnosis even easier.

Here's a simple explanation of what's going on and how to troubleshoot:

The F1 code indicates that:


a. The electronic range control (ERC) is sensing heat in the oven when in a time-of-day (i.e., not cooking) mode.

b. The ERC is receiving information to run multiple heat functions simultaneously.


Although different components (depending upon the model) could generate the code, simple and straightforward testing using your ohm meter is all you gotta do to test for it.

1. Check the oven temperature sensor. The oven sensor has to be within spec or it will cause the F1 code.
As an example of being out-of-spec, the ERC will generate an F1 fault code when the sensor shows 1650 ohms during a time-of-day mode.
This is equivalent to 350°F in the oven.
The resistance isn't high enough to generate an F2 code (runaway temp) or an F3 or F4 code (shorted/open sensor circuit).
The ERC monitors the sensor circuit after a heat cycle and expects the resistance to drop back to 1050-1100 ohms.
The fault code is generated when this doesn't happen. Checking the sensor circuit means also checking the harness,
harness connections and the sensor itself.

2. If the oven sensor circuit checks okay, then turn your inquisitive eyeballs to the touchpad.
If the range has a separate touchpad/keyboard, the keypad may have moisture that is shorting several circuits simultaneously.
If the F1 code is given immediately (instead of during or after a heat cycle),
remove the ribbon connector from the touchpad to the ERC after clearing the F1 code. If the F1 code does not return in five minutes,
then cast a suspicious gaze upon the touchpad/keyboard. Shorts may be caused by using an ammonia-based glass cleaner.
The touchpad surface will absorb ammonia-based cleaners that are sprayed directly on the glass surface. When heat is applied,
the surface material can break down causing shorts.
If you're gonna use ammonia-based cleaners on your control panel, then you should spray it on the rag and then wipe the touchpanel
-don't spray directly onto the surface of the touchpad.

3. On Amana ranges with a rotary temperature dial, be sure that the knob is in the OFF position when performing tests.

4. If these tests all check good, then replace the ERC.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
gy^%$^

Jun 08, 2009 | Kenmore 92320 / 92321 / 92322 / 92324...

1 Answer

Timer tone goes off with F1 display


Hi arl3933,

The "F1" error code description is a System Watchdog Circuit. Please press "CANCEL", if beeping continues after 30 seconds, please check the main control board(ERC). Here are basic test that will help you to determine if the ERC or touchpad is defective.

1. Unplug the range power cord or turn the power off to the range at the circuit breaker.

2. Gain access inside the control panel.

3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC.

4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was.

5. Turn the power back on.

6. Wait for at least one hour to see if the code comes back.

7. If F1 comes back, replace the ERC. If it does not, replace the touch pad.

Hope it helps.

Thank you for using FixYa.

May 14, 2009 | Dacor Preference RSD30 Gas Kitchen Range

1 Answer

The display at top of stove is showing "F1" and continuously beep


Maytag Range / Stove / Oven Fault Codes Failure Code Fault Code Description Solution F0 Function key stuck Replace touch pad or if touch pad is part of the clock, replace the clock (ERC). F1 Defective touch pad or clock (ERC) Replace touch pad or clock (ERC). Touch pad is a more common problem. Refer to F1 test at the top of this page for more information. F2 Oven temperature too hot Replace relay board, if present, or oven temperature sensor (RTD). Check sensor harness. F3
or
F4 Shorted or open oven temperature sensor (RTD) Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok. F5 Watchdog and hardware conflict Replace clock (ERC). F7 Function key shorted or stuck Replace touch pad or if touch pad is part of the clock, replace the clock (ERC). F8 Analog / Digital problem Replace clock (ERC). F9 Door latch Check door latch components.

Mar 19, 2009 | Maytag PGR5710 Performa Gas Kitchen Range

1 Answer

Display shows error code "F1"


F1 Failed Thermistor Control Replace Electronic Range Control (ERC)
Good Luck and Please Rate Fixya!

Jan 06, 2009 | GE Profile Spectra JGBP79 Gas Kitchen...

1 Answer

What does "F1" mean? The oven is out!


I think f1 is a problem with the oven control board. Look on the back of the oven for a tech sheet and it will tell you what the codes mean and what to check.

Sep 24, 2007 | Crosley CE35111AA Electric Kitchen Range

3 Answers

F7


No F7 in my tech sheet Could it be a F1 Failed transistor in control If code cannot be cancelled, replace the Electronic Range Control (ERC) or touch pad if you want to do it yourself let me know...

Aug 25, 2007 | GE Profile Spectra JGBP90 Gas Kitchen...

Not finding what you are looking for?
Maytag MGR5880BDS Gas Kitchen Range Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Kitchen Ranges Experts

gbob59

Level 3 Expert

2963 Answers

freddyfox

Level 2 Expert

236 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Are you a Maytag Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...