Question about Pioneer Projection Televisions

2 Answers

Pioneer PDP - RO6U Plasma: Says starting up, please wait when turning on. Can't get past this screen. I have tried unplugging and plugging everything back in and am still getting the same error. Are there ant other possible solutions to solving this problem other that having someone from Pioneer come out to the house?

Posted by on

  • 2 more comments 
  • mgrubb Sep 15, 2008

    Thanks Sammy... Should I be holding the power button on the TV monitor or the Pioneer box?  Also should I hold for 20 seconds before or after powering up.  Sorry if this sounds like a dumb question.  Thanks for your help.

  • mgrubb Sep 15, 2008

    I unplugged both the plug from the TV screen and the Pioneer box. After waiting an hour, held the power button to the TV for 20 seconds. After doing this, I plugged both sources back in and tried to turn the TV on with the remote. TV is turning on but I am still getting the same error. Is there anything else I can try??

  • mgrubb Sep 15, 2008

    Pioneer Plasma PDP-RO60: Can't get past the screen "Starting up please wait" in a grey box at the bottom of the screen. TV and receiver eventually shut themselves off after about a minute and blue light continues to flash on the receiver. Volume on TV works but no picture. I have tried unplugging and plugging back in in different orders. Not sure what else to try. Anyone's suggestions would be appreciated. Thanks.

  • mgrubb Sep 15, 2008

    1) The tv shuts down after about a minute of displaying the error screen.
    2) The led on the tv turns red.  The media box flashes blue about 12 times and then stops for a few seconds and starts flashing again.
    3) When the tv is displaying "starting up" the led's on the TV and Media Box are solid blue.


    The model of the tv is PDP-436PU/KUCXC


    Thanks

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 203 Answers

Few questions and I might be able to get you an answer. 1) does the tv stay on for as long as you let it displaying this screen? or does it shut down after awhile. 2) If it shuts down what does the led's do on the front of the tv and or media box. 3) what are the led's on the front of the tv and or media box doing while the tv is displaying "starting up".

Let me know and I will be able to better assist you.

Posted on Sep 15, 2008

  • experttv
    experttv Sep 15, 2008

    Also PDP-Ro6u is the model for the media unit. what is the model for the montior?

  • experttv
    experttv Sep 16, 2008

    This problem is listed on pioneers technical website, sorry to give you the bad news but your DTB Assy is most likely defective. This is a board inside of the MRU and should really be changed by a professional. unfortunately its probably going to cost you somewhere between $800-$1000. If you want to try this yourself you can contact pioneer and see if they will sell you the part. part # AWE1305 you can also find it on partstore.com i think. remember im not there to diagnose your set and troubleshoot it so this is the best answer I can give you with the information that i have. I am however 90% sure this will fix your problem. So if you decide to buy the part and fix it yourself you need to check with the company you are getting it from and see what there return policy is and if they are going to charge you a restocking fee for returning the part. Hope this answers all your questions. If you need more help or info just ask!



    Good luck!

    Tim Nolan

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 264 Answers

Unplug it from the power for one hour. Than Press and hold the power button on the on the TV for 20 seconds(It wont show anything. Than Release the power button....

After that plug the power and check the same...

Posted on Sep 14, 2008

  • Sameer Kashyap Sep 15, 2008

    You have to unplug the power source of the TV. While it is unplugged you have to press and hold the power button on the TV. It is a step to discharge any static charges which gets developed. It would not show anything. After 20 seconds you may plug the power in and try turning on the TV again.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MY Pioneer Plasma PDP RO6U is not responding. The Standy light and Rec Time lights were both red and would not turn on either by remote or by pressing the on button on the receiver. I have unplaugged it...


Hi,

As you have already Reset the TV by unplugging it for Few Minutes, and still it did not work, more often it is a Hardware Fault.

Now, I would need few details from you :-

1. Tell me the Number of Blinks?
2. How old the TV is?
3. Do you have any Soldering or Electronic Repair Experience?

Let me know,so that we could Proceed.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Jun 06, 2010 | Projection Televisions

5 Answers

I have a plasma tv that has two black lines about 50mm wide running vertically in the centre of the screen


Three kinds of detects count for this problem. It could be the Logic board, or the Logic Buffer board, or the PDP panel. Just drop your tv to the warranty depot shop to repair.


Aug 17, 2008 | Projection Televisions

1 Answer

My Pioneer Plasma Display Model PDP-424mV must be set on a timer as it will turn off approximately 90 seconds after being turned on . I cannot find the "timer" menu selection. How do I fix this?


try looking on your remote, look for a sleep button and proceed to deactivate the sleep timer using the arrow buttons. if this is not the case, then perhaps your internal cpu is allowing the TV to start, then detecting a problem and forcing the tv to turn off again, though i don't see how it would be possible in this case. there are many others better suited to answer that question other than me, but the sleep button is a good start =)

Dec 03, 2009 | Pioneer Projection Televisions

1 Answer

I have a Pioneer PDP 60 inch plasma tv and I just recently noticed a thin line just right of center that starts at the bottom of the screen and goes straight up about 12-15 inches long. When certain colors...


This is Most likely a small crack in the screen the color is actually from the plasma it cant be fixed by yourself but i would reccomend checking the warranty or try taking it back

Nov 24, 2008 | Projection Televisions

1 Answer

I have a pioneer 50 inch plasma model no pdp507xda i need a new screen how much will it cost cheers


part #AWU1316 Pdp Service Panel it is listed as no longer avaible because they do not sell the pdp to the public or non service centers
sorry
scott

Nov 04, 2008 | Pioneer Projection Televisions

1 Answer

My pdp r03u has an error code e01


I have a 50" Unit with this same part, I called Pioneer and told them what was happening, they asked me to count the flashes on the monitor power indicater light and when I told them the problem they told me that it was a dry solder weld, I called a tv repair tech and told him what was going on, he had never worked on Plasma Tv's and was very hesitant to start I told him if I just brought in the Media Box and had him check the solder joints how much would he charge he told me to try he wouldnt charge me anything, I jumped on that! he saw a few issues and fixed them, I brought the unit home plugged it into the tv and the tv works just fine!

Oct 24, 2008 | Projection Televisions

1 Answer

Pioneer plasma media receiver problem



The Pioneer multi media reciever box is only serviceable from the manufacture. They should have authorized service reps that they equiped to do service for Pioneer devices. They normaly change boards to service it. The regular service man would only be able to fix a simple cold solder connecton or fix some other simple part of it.

Contact the place where you bought it to find out about servicing it. You may find it cheaper and easier to simply replace it completely. It is very possible that there is no service support for this box. Get an estimate before accepting to service it.

Most of the small electronics of today are throw-away anyways...

Jerry G.

Apr 13, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

412 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

zorbrack

Level 1 Expert

19 Answers

Are you a Pioneer Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...