Question about Projection Televisions

2 Answers

Connecting Digital Decoder to Analogue TV.

Telefunken analogue color TV model MP-A2055VT-H
to connect up digital decoder set-top box.
The TV only has an RF input. no other plugs. Searched all 80 channels and I cannot find an AV channel on the Telefunken to receive the digital decode.
How is AV input to his set accomplished?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 300 Answers

This whole things is about converting the output of your digital decoder box to RF since your TV set only has an RF input

Lets look at the two main standards Composit and S-Video

1. if the output of your digital decoder is Composit you will need to convert it to RF using a Composit to RF converter.

RCA makes very small cheep ones that use about 9volts of power and can convert Composit into RF

2. if the output of your digital decoder is S-Video you will need an S-Video to RF converter

S-Video output is the newer standard but is essentialy the same as Composit and low cost.

Shalom ..



Posted on Sep 14, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 505 Answers

The av channel is 0 and then you need to search on channel 0 as i mean tune into the channel

Posted on Sep 14, 2008

  • as you would tune into network channel for an rf connection tipe

×

1 Suggested Answer

kevin000
  • 1847 Answers

SOURCE: Telefunken analogue color TV model

you have to change the port at the back of the TV. shift to another input.

Posted on Sep 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cant seem to tune in after digital switch over not got any chanels


If your TV is an older variety that wasnt set up for digital signal you will need a set top converter box.

Jun 22, 2011 | Toshiba Projection Televisions

5 Answers

Telefunken analogue color TV model MP-A2055VT-H to connect up digital decoder set-top box. The TV only has an RF input. no other plugs. Searched all 80 channels and I cannot find an AV channel on the...


Hi,

The simplest solution would probably be the use of an RF Modulator. Feed the RF Mod with the A/V signals from the Conia CSTB12, set it to transmit on Ch 3 or 4, tune the Telefunken to either channel.

In most Telefunken TVs we have worked on, the A/V INput/OUTput would be on the SCART connectors as shown below.
9775210.jpg
To my understanding, a Conia CSTB12 as sold in Australia has a composite RCA (yellow) Video OUTput and L/R White/Red audio OUTputs. What would be needed would be a A/V signal to SCART adapter/converter.
7906648.jpg
If your Conia CSTB12 has an S-Video, then this may be used.
If your Conia CSTB12 has an HDMI, then something like this may be used.
Incidentally, should you be interested, there are comparable receivers to a Conia CSTB12 that has SCART OUTputs.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.



Sep 14, 2008 | Projection Televisions

1 Answer

Can you tell me how to tune in a channel when ppreparing to use a freeview box on a onyx sw 1536 ld


Unless you've got an "expensive" Freeview box that modulates its output on to the RF (Aerial) connector then you can't. Most Freeview boxes have 2 aerial connectors - 1 IN from the Aerial itself and 1 OUT to connect to the TV - BUT this is ONLY a PASS-THROUGH connection. This means that the digital Freeview signal which is decoded from the aerial signals is NOT output on the OUT connector and sent down the co-axial cable to your TV. Only the "old" ANALOGUE (not Freeview NON DIGITAL) comes down that co-ax. What you should do is connect the Freeview box to your TV with a SCART cable via the SCART connectors on both. You need to select the AV input on the TV using the remote.
Even if you do have an "expensive" box that does modulate the digital decoded programmes and output these of the RF OUT connector, you should still use a SCART cable as the picture produced will be far better
Hope this helps

Jul 06, 2010 | Projection Televisions

1 Answer

I would like to know if the Hitachi 51UWX20B television can be connected to the internet.


Your Hitachi 51UWX20B is an HDTV-Ready TV. No Digital Tuner. HDTV-Ready means that your TV set is capable of displaying analog and high-definition digital pictures, but without a digital tuner, it cannot receive the digital signal. An HDTV-Ready requires an external high-definition TV receiver (digital tuner) in order to receive HDTV signals. These external receivers can be called an HDTV Tuner, set-top-box, decoder or DTV Converter Box . So you will be required to purchase a converter box to receive over the air programming from an external antenna.

Jul 03, 2010 | Hitachi 51UWX20B 51" Rear Projection...

1 Answer

RCA D56W20 picture problems


More information is required to properly troubleshoot this problem. How is your television connected when you are watching HD? Do you have HDMI for this, do you have a satellite or digital cable box? For analogue are you using regular coax antenna (cable TV), or are you going through a cable or satellite box?
This could be related to the aspect ration setting. perhaps you ahve changed your aspect ratio from 16:9 to 4:3 or some other setting. If you are connected via HDMI, then the digital signal may be "normalizing" your picture during HD, but reverting back to the other setting.

Check you video settings very carefully. HD televisions are very difficult to tweak properly.

Sep 03, 2008 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

WHARFEDALE LCD2610AF WHEN I TURN ON DIGITAL I HAVE PERFECT PICTURE &SOUND.AFTER 10 TO 30 MINUTES THE PICTURE FREEZES AND THEN SCREEN TURNS WHITE WITH AGREEN HORIZONTAL BAND LOWER HALF OF SCREEN.WHEN...


Hi.

If the picture & sound are ok in analogue mode then chances are you have problem with digital tuner.
This may be expensive to repair so I would advise connect external freeview box or sky etc to get digi channels using scart to connect to your TV.

Jul 16, 2008 | Projection Televisions

1 Answer

Wide screen adjustment does not hold keeps going to default narrow screen


Hi,

Most analogue TV's do this because the analogue signal has no way to tell the TV that its a widescreen picture.

European TV's that use scart cables have a switching pin on the cable so the digital set top box can tell the TV that the picture is widescreen.

If you're in the US or down under this info wont be much help though.

Hope this helps

Andy

Jun 26, 2008 | Projection Televisions

1 Answer

Will this tv work without a converter box when everything goes digital?


Hi.

If your set only has Analogue tuner you will need either Sky. Virgin, Freesat, or freeview box to be able to watch TV channels.

Jun 22, 2008 | Projection Televisions

1 Answer

Hi guys, don't know if the previous post got through. Have a new LCD tv and DVDr, connected with a HDMI cable. when DVDr switched off analogue and digital picture is fine. as soon as dvd is switched on...


yes, hdmi will give you better results..
are you running hdmi to hdmi connection on tv from cable box?
if so, that is correct but as for the dvdr, what tv port are you connecting it to? i would use another hdmi cable for the dvd too for best picture resultif it's an option on your dvd.. you should have multiple input outlets on your lcd with 1-3 options for input devices via analog or hdmi.. so analog is not hdmi--hdmi is digital so it switches to the hdmi resolution when you turn it on..

let me know how it goes and if i was helpful involving resolution.. helpful feedback is appreciated.. thanks, d

your dvd player should be set to a different

Feb 27, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...