Clean light flashes

Thank you! Problem Solved! We were about to call a repair man!

solution 2 is the best which is as follows..

The clean light sometimes flashes and just needs to be reset. To do so hit the keys in the following order. <Heated Dry> <Normal Wash> <Heated Dry> <Normal Wash> <Cancel>.

The dishwasher will go through a cancel cycle (drain the tub) and will then let you start it up again..the pressing of the buttons takes several attempts. the lights on the front panel will all light up and the washer will go through a cycle. it will be fixed upon completion of the cycle

The clean light sometimes flashes and just needs to be reset. To do so hit the keys in the following order. <Heated Dry> <Normal Wash> <Heated Dry> <Normal Wash> <Cancel>.
The dishwasher will go through a cancel cycle (drain the tub) and will then let you start it up again.

Hi, the reason why you are getting the flashing light is because the dishwasher failed to detect a 4 degrees rise in the water temp during the first 8 minutes of the cycle. Some reasons for this is a faulty heater, door switch,(heater runs through the nuetral side of the door switch), lack of water, d/w not filling correctly, should be just below heating element. Clear the fault by pressing heated dry,- normal,- heated dry,- normal. This will put you in the diag mode. Just let it do it's thing from there. It would help a lot if you run the hot water at the tap before starting the dishwasher after you clear the code..hope this gets you on your way..

It sound like a water supply problem to the dishwasher.
Check first that water supply pipe isn't bend. Water supply to the dishwasher is done through an electromagnet valve,loocated at the pipe's enterance to the machine. Test that it get power (with a multi- meter). In case it get power and dosen't work - You can easyly open the valve and clean it (from scale or other dirt). Be aware you should disconnect the power cable from the machine before doing it !!!!!
Check as well for valve's coil resistance. In case you have no resistance measurement - you should replace for a new valve.
Good luck !

TAPE THE INSTRUCTIONS TO CABINET INSIDE THANKSIT WORKED

Okay, I tried all of the above and each time I try to run the DW., it will stop at the dry cycle and the clean light flashes green 7 times and I have to start all over to reset it. I did call a repairman and he came out and said I need a new heat element. Then, when the company called to set up date and time to fix it, they claim that 2 parts were needed...heat element and the board and the whole thing was going to cost $279.00. I just had my kitchen remodeled and can't help but think this has something to do with when the put the DW back and hooked it up. It worked fine up until that point. The repairman says it's just a coincidence. Now I'm wondering...?? I just don't trust repairmen in any trade really.
Sorry, but that's how I feel being a woman and feeling that we get taking advantage of many times.

OUTSTANDING!!
I had the exact problem and this tool worked perfectly.
Thanks a ton,
I saved almost $150 on a part (element) and a service call.
I originally called Sears Service for a call, I told them the problem and set a date for a week away.
After doing the arranging I called a Local Repair and the Service Tech told me of Fixya and mentioned a reset sequence to fix my problem.
He/They would have serviced it this evening, but he told me to first try the reset. I can hear it running a cycle as I type in the background.
Amann Appliance Service in Hamilton Ontario Canada was perfect.
Thanks a ton,
John in Ancaster

Thank you so much, very cool website, it worked, my dishwasher is running

Solution 3 & 5 did the trick - THANKS for saving me the repairman cost!!!!

Thanks for solving the problem my dishwasher was having!!!

Thanks!!!!! Saved $200 for a service call plus who knows how much for parts. What a rip.

the reset did the trick for me! thanks for the tip!

solution number 3 worked after switching off the breaker for 30 minutes. i would have unplugged the dishwasher but it is bolted under the cabinet. thanks!