Question about Air Tools & Compressors

1 Answer

Paslode 5300/75S Framing nailer

After I put a kit in to the nailer the gun will not cycle and the trigger leaks air when depressed

Posted by on

  • 1 more comment 
  • Dane Lanne
    Dane Lanne Jan 01, 2009

    I have the exact same problem!Put a rebuild kit in,replaced 100% seals and trigger assembly,and same thing still happens!

  • bostich May 11, 2010

    Stanley bostitch, ridge runner, roofing gun.

  • Owen Braby Sep 13, 2014

    Did you replace or try to rebuild the trigger. It should only be replaced.

×

1 Answer

Soory It is a roofing nailer not a Paslode framing nailer. ended up replacing the main valve. all is well now. thanks

Posted on Sep 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I put a new o ring rebuild kit in my Bostitch N80 sb framing nailer. I replaced every o-ring (including the trigger valve assembly


If the new trigger valve leaks air when you connect the air supply, most likely defective valve or air is leaking past outer trigger valve orings due to debris in the slot or new orings were cut when the valve was pushed in. If air leaks when you depress safety to fire gun then most likely problem is in the head valve or safety foot is not pushing the firing pin all the way in. Easy test, remove nails and remove the trigger to expose the firing pin. Connect air and very quickly depress the firing pin all the way in. If the gun fires, adjust the safety foot as needed. If the gun does not fire, remove the head and check headvalve orings for good snug fit against the cylinder within the head. The surface were orings make contact must be very smooth and not too deeply worn. If you notice fine scratches remove with fine sandpaper. Reinstall head using plenty of white grease on all the orings within the head and retest. Good luck

Feb 10, 2013 | Stanley Bostitch N80CB Coil Framing Nailer

1 Answer

Paslode 350 Framing nailer trigger does not fire.. Has worked until today, has the correct pressure, but the trigger feels dead.


make sure the safety is not bent what you can try and be careful is remove ALL nails and plug the tool into the air supply, find a small screwdriver and holding the nose up off work use the screwdriver to depress the trigger valve, if it works then you have a safety issue, if not then you have a trigger valve issue. Let me know if you need more help

Jan 18, 2011 | RTO PasLode 900420 Impulse Framing Nailer

1 Answer

Plaslode im250 second fix nail gun fires intermittently. Gas is loading fine and trigger working only fires about one in every ten pulls of trigger


Hi,

Here is a tip that I wrote about the Paslode nailers and the problems that can come up with them.

I also have a link to the Paslode manuals which contain Paslode cleaning and troubleshooting guides.

If you need parts for your Paslode, there also is a link for a site that sells the Paslode nailer parts.

Paslode Cordless Nailer Problems



heatman101



,/,/,./

Dec 31, 2010 | RTO PasLode 900420 Impulse Framing Nailer

1 Answer

Paslode f350s.just replaced all o rings,now when you pull the trigger air leaks out through the trigger,but only when depressed..will not fire nail.please help ..thanks bob


Simple. You have a leak you didn't have before. Either find it, or take it to someone who knows what they're doing. O-rings have a thickness, as well as a diameter. If you used generic rings, that's probably the problem. Use the repair kit by Paslode.

Paslode.com can tell you where your nearest dealer/repairer is.

HH

Dec 05, 2010 | RTO PasLode 900420 Impulse Framing Nailer

1 Answer

Gun is only a few yrs old and has had moderate use. Problem is that when depressing the nose piece I get a hissing of air and it will not fire. It will sometimes fire but after a few nails it just hisses...


Your o-rings are wore out. Paslode makes(made) a Tool Repair Kit, PN219235 and Trigger Valve Kit, PN219224 for your gun. Always use all of the o-rings in the kit and liberally lubricate them before installing them using grease in the kit or nail gun oil. If the kits are no longer available you'll have to get a breakdown of the gun, (www.paslode.com/uploadedFiles/PowerMaster_Plus_Parts_Diagram_Schematics.pdf) and order all of the o-rings. Be very carefull to put everythng back together properly, you are working with a gun.

Aug 31, 2010 | NRS Paslode 501000 Powermaster Plus...

1 Answer

Paslode battery wont hold charge.brought new battery, same thing.brought new charger, same thing. put battery in gun, fan runs and then the battery is flat again.


if you have bought a new battery and charger , and it still will not hold a charge. you might have bought a bad battery or charger , also the fan dosent allways run so the fan going off is not a sign of a dead battery. depress the trigger or safety and the fan should start up again

Feb 14, 2010 | RTO PasLode 900420 Impulse Framing Nailer

2 Answers

Need Parts for Central Pneumatic Air Framing Nailer D1CN28/90


I have a Central Pneumatic Frame Nailer the driver will go down but not back up unless you disconnet air supply.

Aug 11, 2009 | SK Paslode Sk312 Framing Nailer O`ring...

1 Answer

Paslode nail gun not firing


Hi,
Yes you need to oil driver blade piston.
You need to check for spark. With no nail or gas in it. Take of main cylinder(4bolts on top, 2 bolts on nose. And then put in battery. And then push upper switch(behind roller at top) and the fan will come on. And then pull the trigger. You should have spark.
Thanks,
Jeff

May 16, 2009 | RTO PasLode 900420 Impulse Framing Nailer

1 Answer

Paslode framing nailer loss of power.


Here's what I found at the Paslode Troubleshooting Site:
Tool will not cycle - fan runs, indicator light
is solid green.

Lockout bracket is stuck in lockout position.
Work-contacting element is bent, or build-up of
debris in track restricts operation.
Follower is not behind fasteners.
Fuel Cell empty.
Spark wire out of spark plug.
Spark plug is dirty.
No spark is generated.
Check lockout.

Remove and inspect lower probe. Clean and
lubricate track with Paslode Impulse® oil.
Repair or replace lower probe as required.
Position follower behind fasteners.
Replace fuel cell.
Remove cap and check spark lead, insert in
spark plug and replace cover.
Clean tool cylinder head and spark plug.

If this doesn't work, I suggest contacting Paslode directly 800-222-6990

Mar 11, 2009 | RTO PasLode 900420 Impulse Framing Nailer

Not finding what you are looking for?
Air Tools & Compressors Logo

Related Topics:

1,213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Air Tools & Compressors Experts

John Trevino

Level 3 Expert

1378 Answers

Brad Brown

Level 3 Expert

13765 Answers

james allen
james allen

Level 2 Expert

109 Answers

Are you an Air Tool and Compressor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...