Question about Amana Dryers

1 Answer

Gas dryer ALG643RBW ignitor glowes but no flame

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 943 Answers

Hi thanks the problem is with the coils at the gas valve 2 small coils 1 with 2 wires 1 with 3 replace Thanks THE APPLIANCE DOC

Posted on Sep 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ignitor glows but short cycles


Ignitors don't "blow flames". But a defective ignitor can glow but not draw enough current to allow the gas valve to open to the burners.
Replace the ignitor. It's the "weakest link" and most likely part to wear out through use in the ignition system.

Sep 19, 2012 | Amana NGD5200TQ Dryer

1 Answer

Model ALG643RBW Dryer heats sometime, APPEARS Flame Doesn't Always Ignite.


Hi,

If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.



if you dryer is gas check out this gas no heat tip....



If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.



check out this electric no heat tip...


heatman101
................

Nov 22, 2010 | Amana ALG331RAW Gas Dryer

1 Answer

Why wont my dryer heat up


Check the ignitor underneath the drum. (You have to open the panel to see it) It should glow shortly after the dryer starts, then the flame starts and the ignitor shuts off. If the ignitor does not glow then it or the thermostat is bad. If the ignitor is glowing but the gas does not light then the flame sensor may have to be replaced. If the gas ignites but does not stay on either the flame sensor or the coils are at fault.
See also: http://home.howstuffworks.com/how-to-repair-a-dryer.htm

If everything above is OK then the thermostat2.gif or the auto sensor is not working correctly.

Nov 26, 2009 | Whirlpool LGB6300 Gas Dryer

1 Answer

Dryer is not putting out heat. Gas is connected and working in other parts of the house near the dryer.


Check the ignitor underneath the drum. (You have to open the panel to see it) It should glow shortly after the dryer starts, then the flame starts and the ignitor shuts off. If the ignitor does not glow then it or the thermostat is bad. If the ignitor is glowing but the gas does not light then the flame sensor may have to be replaced. If the gas ignites but does not stay on either the flame sensor or the coils are at fault.
See also: http://home.howstuffworks.com/how-to-repair-a-dryer.htm

If everything above is OK then the thermostat2.gif or the auto sensor is not working correctly.

Nov 24, 2009 | Roper RGX4634KQ Gas Dryer

1 Answer

I have a whirlpool dryer.... the blower works fine but will not heat up any suggestions


First thing to check is the ignitor underneath the drum. (You have to open the panel to see it) It should glow shortly after the dryer starts, then the flame starts and the ignitor shuts off. If the ignitor does not glow then it or the thermostat is bad. If the ignitor is glowing but the gas does not light then the flame sensor may have to be replaced. If the gas ignites but does not stay on either the flame sensor or the coils are at fault.
See also: http://home.howstuffworks.com/how-to-repair-a-dryer.htm

Nov 12, 2009 | LG DLE0332 Gas Dryer

1 Answer

FLAME ON SART UP NONE AFTER


Replace the gas valve coils if the ignitor glows but does not light. Replace the flame sensor if the ignitor does not glow.

Aug 29, 2009 | Kenmore 73952 Gas Dryer

1 Answer

Gas dryer tumbles but is not heating up


First thing to check is the ignitor underneath the drum. (You have to open the panel to see it) It should glow shortly after the dryer starts, then the flame starts and the ignitor shuts off. If the ignitor does not glow then it or the thermostat is bad. If the ignitor is glowing but the gas does not light then the flame sensor may have to be replaced. If the gas ignites but does not stay on either the flame sensor or the coils are at fault.

Aug 25, 2009 | Dryers

1 Answer

Dryer Model DE306 has stopped heating


First thing to check is the ignitor underneath the drum. (You have to open the panel to see it) It should glow shortly after the dryer starts, then the flame starts and the ignitor shuts off. If the ignitor does not glow then it or the thermostat is bad. If the ignitor is glowing but the gas does not light then the flame sensor may have to be replaced. If the gas ignites but does not stay on either the flame sensor or the coils are at fault.

Aug 13, 2009 | Dryers

Not finding what you are looking for?
Dryers Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amana Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you an Amana Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...