Question about Dishwashers

1 Answer

My ge quietpower 2 dishwasher leaks all over the floor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,239 Answers

HI The door of the dryer is sealed with one or more gaskets to keep the hot air in the dryer from escaping and prevent the cool air in the laundry area from being sucked into the dryer. A deteriorated or damaged gasket greatly lowers the efficiency of the dryer. To check the gasket, hold a sheet of tissue paper near the rim of the door while the machine is running. If the door leaks, the paper will flutter. If the gasket or seal leaks, looks worn or warped, has chunks of material missing, or feels hard and nonresilient, it should be replaced with a new gasket of the same type.
THAKS/..............

Posted on Sep 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where does the ball filter on my ge dishwasher go


GE WD12X10408 Ball Filter-Orange - AppliancePartsPros ...

www.appliancepartspros.com > GE > Dishwasher > GE Dishwasher Parts

Rating: 4.5 - ‎2 reviews - ‎$7.74
BALL FILTER-ORANGE WD12X10408 / AP5645087 made by GE. ... I had asked you previously about my dishwasher issue with it not draining like ... Does the filter ballaffect the draining of the dishwasher and if so does it sit in the ... It goes into the top of the nozzle tube on the left side of the sump inlet part # WD18X10039.

GE Dishwasher - Plastic Ball Sump Filter Question - Appliance ...

forum.appliancepartspros.com > ... > Dishwasher Repair

Dec 11, 2012 - 9 posts - ‎1 author
I had a water leak from the dishwasher on Saturday and found that some critter. ... and found that some critter had chewed a hole in the bottom of my sump. ... want to put it back together but I don't know where this ball goes. Water does not drain completely
8 posts
Sep 17, 2012
GE QuietPower Dishwasher will not drain 100%
10 posts
Oct 18, 2010
Hotpoint dishwasher won't drain
10 posts
Jan 18, 2010
white balls in dishwasher where do they go?
2 posts
Nov 25, 2007
More results from forum.appliancepartspros.com

I have a GE Dishwasher model GSD


Jan 19, 2016 | GE Dishwashers

1 Answer

FILLS, DOES NOT WASH, THEN DRIES


GE GLDT690TBB Fully Integrated Dishwasher with 7 Wash Cycles Including SaniWash and SpeedWash, Nylon Racks, Stainless Steel Interior, Countdown Display and QuietPower 56 Quiet PackaBlack- Recent Questions, Troubleshooting & Support

Oct 07, 2015 | GE GLDT690TWW Fully Integrated Dishwasher...

1 Answer

Dishwasher troubleshooting


Remove them and check that they don't need cleaning. The top ones usually move with the power of the water going through them. If they are blocked the water can't get through and they can't turn.

Aug 11, 2014 | General Electric Dishwashers

1 Answer

My office's GE QuietPower 3 dishwasher detergent


Hi,
There are three common problems that cause the Soap Dispenser or Cup not toopen. I have a tip that will explain these problems in detail....

Dishwasher Repair Problem Detergent Cup does not Open

heatman101

Jul 29, 2011 | Maytag Dishwasher

1 Answer

No water in dishwasher


check the water valve it could be bad and not be letting water into the unit...let me know and I will further assist you.

May 13, 2009 | GE Dishwashers

1 Answer

GE QuietPower 2 has three lights flashing, and won't work


Its the reset cycle... give it a few minutes, and it will be ready to go..

Apr 20, 2009 | Dishwashers

1 Answer

Water input leaking on GE QuietPower II model GSD4030Z04WW


Hi,


Solution:
Sounds like the drain pump has been leaking from the seal where the motor shaft goes into it.

Usually you pop off the 2 metal clips, and pull the drain pump off the motor shaft.
If yours won't come off easily, chances are the motor shaft has expanded from corrosion, seizing the drain pump onto it. You can try prying it off by wedging a screw driver between it and the motor (be careful not to damage the motor). Last resort is to break the drain pump into pieces to remove it.
You will likely have to sand or file the motor shaft back into shape to install the new drain pump.

thanks,

any further question don't hesitate to contact me.

Mar 18, 2009 | Dishwashers

1 Answer

QuietPower 3, water seeps into unit,fills the base once per week.


I need more info but I would check the drain connection under the sink to make sure that it goes up after leaving drain , to keep the sink from draining into the dishwasher.

Dec 14, 2008 | GE 24 in. Profile PDW7800 Built-in...

2 Answers

GE Adora QuietPower II Replacement Rack Wheels?


Model number is on a sticker on the left wall of the dishwasher, just behind the door, about mid tub level. Post your full model number and I'll list your part number(s) for you.

Sep 06, 2008 | GE Adora GHDA656LSS Stainless Steel...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

453 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...