Question about Sylvania 6319CC 19 in. TV/VCR Combo

1 Answer

Remote control no longer works

My remote control gradually stopped working. It took several times of aiming it at the tv before the channel would change then eventually I got no response from the remote to the TV. I changed the batteries twice and still nothing. I can't use the menu for set info because the remote is not responding. I can change the channel & volume and vcr will work if I manually touch the buttons on the front, however I can't access the menu in anyway because that is done through the remote control.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 3,130 Answers
Re: remote control no longer works

An original remotes available for ya at for 30 bucks + shipping

Posted on Apr 23, 2006

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Cannot enter correct code for dish network remote control

Try these steps:

Power Scan
1.) Hold down the clear "TV" button on the remote for four seconds, then press 500 pound ( #)
2.) Hold down the clear "TV" button on the remote for four seconds, press the big power button once.
3.) Press the channel up button once per second until the TV turns off then press pound (#).
When you finish several functions to make sure the remote works. Hope this helps!!

Daniel Busa
DISH Network Customer Service

Feb 26, 2011 | Emerson EWC27T3 27 in. TV/VCR/DVD Combo

1 Answer

I have a magnavox CT270MW8 tv that started by turning on by it's self and flippping through the channels very fast, and when it would do this the remote control would not work nor would the controls on the...

There is some problem in semi conductor install inside TV from where it catch signals from remote, detect frequency and change and adjust your desire frequency and then your fav channel comes on screen
get it repaired only that part which receive signals from remote
If you like. Kindly rate

Sep 21, 2010 | Combination Televisions

2 Answers

Need tv code for Quasar LSSQ0227 its a comcast

had this problem myself and I assure you that a) Comcast is populated by idiots without training, and b) that Quasar hasn't 'deliberately designed' their tvs to not work with Comcast remotes, which is what Comcast will tell you.
Solution: Add a 1 to the code, ie 10250, 10051 etc. Quasar is a 5 digit code, not 4 as Comcast believes.

Feb 06, 2010 | Quasar VV-1302 13 in. TV/VCR Combo

2 Answers

How to select av without remote control

try pressing plus and minus channel on the tv at the same time. works with my daughters tv

Nov 16, 2009 | Bush DVD142RC 14 in. TV/DVD Combo

1 Answer

Tv on/off and volumn don't work on my dish remote


If you are trying to use a Dish Network remote control, then you are probably out of luck. Most Dish remotes do not have remote codes for TV/DVD or TV/VCR combos. There are just too many codes out there to put into one remote control. I'm sure they tried to walk you through a code search (hold the TV button down, etc.), so if it didn't show up then, then you are probably stuck with using two remotes or adjusting manually.

If they didn't try a code search, then try this:

Turn the TV on manually. Then, press and hold the clear TV button at the top until all the buttons at the top turn red, then release. Press and release the TV power button (the smaller red power button), and press the channel up button. Repeatedly press and release the channel up button about once a second until the TV turns off by itself, then press and release the # button at the bottom right hand corner of the remote, and the TV button will flash 3 times, confirming that it took the code. Press and release the clear SAT button at the top left, and then you should be good to go.
If the TV never turns off during the code search, and the TV button at the top of the remote flashes a bunch of times everytime you press channel up, then there are no more remote codes. The remote does not have the code for your TV.

Hope this helps you.

Jan 06, 2009 | Broksonic CCVG297 9 in. TV/DVD Combo

2 Answers

Remote won't work

hi, see if the right funtion is selected, tv, vcr, dvd.then if that does not help, get a universal remote. they don't cost alot or some don't good luck. hope this helps.

Apr 15, 2008 | Toshiba MW27F51 27 in. TV/VCR/DVD Combo

1 Answer

Missing plastic circle: remote doesn't function

If the remote sensor cover is missing on the TV, the remote would still work but you may get other effects like the TV changing channels on it own.
This is due to stray infra red signals.
If it's not working at all I would suspect the remote control handset.
You can test it by pointing it at a digital camera lens and watching the display screen on the camera.
You should see white light comming from the remote when you press any of the buttons if it's working.
Digital cameras can see infrared.

Mar 13, 2008 | Combination Televisions

1 Answer

Remote will not work

No wonder I don't find Emersons anywhere. You can try this , use a TV/AUDIO cable from the back of your cable box to the front inputs. Then use the channel button until you get LINE. You will get TV signal but you still have to turn it ON/OFF manually. Same goes for VOLUME. Good luck.

Jan 17, 2008 | Emerson EWC1303 13 in. TV/VCR Combo

Not finding what you are looking for?
Sylvania 6319CC 19 in. TV/VCR Combo Logo

Related Topics:

299 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sylvania Combination Televisions Experts

Rabeka Drew

Level 1 Expert

27 Answers


Level 2 Expert

310 Answers

The Knight
The Knight

Level 3 Expert

66330 Answers

Are you a Sylvania Combination Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides