Question about Epson Stylus 2200 InkJet Photo Printer

1 Answer

Blinking lights all lights are blinking plus out of paper light is blinking.  Pulled paper out before it could print because it was wrong paper.  Turing off computer and printer does not re set it.  Can't get it to do anything. Any Ideas?

Posted by on

  • 3 more comments 
  • jf49 Oct 01, 2008


    Hello, 
    My Printer Epson Photo Stylus 2200 doesn't work any more.
    Suddenly all the lights plus the paper button light started to blink.
    I have disconnected it(firewire and AC), restarted my computer and 
    reconnected it,  but nothing changed.
    Is somebody resolved this problem before?
    JF 



  • rseeley Oct 12, 2008

    all lights are blinking including paper feed light. i cannot find any info in the user guide. Does anyone know what the problem is? Epson 2200; Oct 12, 2008; richard@seeley.com; Rich Seeley.

  • Aaron25 Nov 02, 2008

    All ink lights and paper light are blinking red!!!

  • mairg Nov 24, 2008

    I have the same problem

  • Justin Goldberg Dec 25, 2008

    I did what you said, but mine is still blinking. Also I didn't clean or replace the waste tank, but still, shouldn't it stop?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Epson Master
  • 541 Answers

This means your printer wast pad is full this is now oyu reset your printer but make sure you have put new pads in 1st and dont for get to rate plz

  1. Turn off the printer power and unplug the power cord from the wall. Disconnect the computer interface cable at the back of the printer.
  2. After one minute reattach the power plug to the wall, but don’t reattach the computer cable.
  3. Hold down the ROLL and the PAPER ADVANCE buttons simultaneously.
  4. Turn the printer on. after 2 blinks, all the ink lights come on, then release the buttons being held down.
  5. Press and hold the ROLL button for 10 seconds.
  6. Release the ROLL button and the printer will initialize, which resets the Waste Ink Pad Counter.
  7. Once initialization is complete, turn the printer power off.
  8. Reconnect the interface cable.
  9. Turn the printer on and print a document.

Posted on Dec 04, 2008

  • Lee Reynolds
    Lee Reynolds Dec 05, 2008

    plz dont forget to rate me thanks

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have error light on. Computer won't print. I just bought the printer and it printed just fine twice. Then I turned off the power when I did not use it. When I tried to print again. the error light is...


The error light that is blinking is actually blinking out a error code. In the back of your manual under troubleshooting there should be a list.

On a printer this new about the only error you should see is a paper jam. IF anything else is wrong I'd just put it in the box and take it back. Rarely do you see something fail this new these days. It happens but not that much.

Once you look up the error code you will know what the problem is. It could be a cable unplugged or a paper jam etc. I can;t see it being serious.

Sep 11, 2011 | Brother HL-2040 Laser Printer

2 Answers

Paper stops half way


Please check for torn piece in the carriage which is causing the error

Jul 06, 2008 | Canon PIXMA iP4200 InkJet Photo Printer

1 Answer

Samsung ml-1640 giving red light, not taking papers


I had the same problem when a paper jammed and I have pulled it out. The red light came on and nothing worked. My solution was: I pulled out the tonner and put it back, opened all covers and closed it. All this apparently must be done with printed turned on (the same thing with printer turned off didn't work). Hope this helps.

Mindaugas

Oct 08, 2009 | Samsung ML-1640 Monochrome Laser Printer

1 Answer

Paper light is on, won't print, but it is full of


I have an HL-1440. The problem was an empty toner cartridge. Got a new one and it prints like a champ again. Good luck.

Aug 05, 2009 | Brother HL-2040 Laser Printer

1 Answer

Green light blinks twice, sayus "User Intervention Required"


Two blinks just says you need paper, If paper is not going through, you will need repairs to the print engine. If the orange light is also blinking you need to count the blinks to know what's wrong.

Jul 02, 2009 | Canon PIXMA iP90 Mobile Printer

2 Answers

I was unsing my printer when it jammed. I cleared the paper however, the alarm light keeps coming on. I have tried turing the printer off, turning off the entire computer, turning the printer and computer...


Normal 0 I suggest you get a sheet of Card Stock (Heavy paper) and place it in the feed way. Then press the print button applying a slight amount of pressure on the Card Stock so it will feed through the printer. The reason for this, is in some cases I have been able to clear the paper track of debris that was deposited there over time.
Worth a try, as I have fixed a number of printers this way, saving costly repairs.
Hope this helps. Bud

Jan 22, 2009 | Canon PIXMA® MP530 All-In-One Printer

1 Answer

Paper light continually flashes won't print


when you lift the cover on the back of the printer there is a thin plastic sensor very delicate normally black in colour which detects whether there is paper in the tray or not.that sensor is slightly moved from its orignal position or broken , so this problem is coming.

thanks.

Sep 18, 2008 | HP LaserJet 4L Printer

3 Answers

Won't print


Sounds like a piece of paper is stuck inside the machine. Open all access doors and check. Remove the printer cartridge and reinsert. Make sure the print job has been purged from the queue.

May 31, 2008 | Lexmark X73 All-In-One InkJet Printer

1 Answer

Print light blinking


turn it off..let it set for 4 min..and then turn it on..try a test page first, though

May 10, 2008 | Brother HL-5240 Laser Printer

Not finding what you are looking for?
Epson Stylus 2200 InkJet Photo Printer Logo

458 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Office Equipment & Supplies Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18381 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Cindy Wells

Level 3 Expert

4949 Answers

Are you an Epson Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...