Question about Projection Televisions

1 Answer

Nikkai A75HQ Digital Freeview Receiver cannot receive ITV1, Channel 4 or Channel 5. BBC programmes no problem

Posted by on

  • Anonymous Oct 26, 2008

    I have the same problem with Nikkai A49GC, unable to get any ITV channels & signal level is 41% on most channels. signal ok when my old Panasonic box is connected, 9 out of10.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I'm using an attenuator 3db/5-1000Mhz - I get all channels. Without I got 100% strength,0% quality. hope it helps

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HI. I have purchased 3 Nikkai A75HQ Freeview boxes from Maplin and cannot get them working with the respective TVs. Have connected via scart, gone through the installation process but the on-screen just...


You must use a good antenna installed in a good position on these receivers - those usual room portable antennas will not work. Or, if you have cable and it has free HD channels, split the cable and use it.

Apr 22, 2011 | Projection Televisions

1 Answer

I have a nw MAT19W127 tv and cannot receive BBC!, BBC2 and BBC3 on the freeview service (BBC4 is OK) Message shown is "No Signal". I have tried reloading the channels but still nothing. Othe...


dear,
in tv a device used called Hyperband, means
Hyperband
In the service channel network, the frequency used for distributing TV stations (300 - 470 MHz). It is the range of choice for digital transmissions according to DVB-C.

sometimes, it happens that the hyperband installed in tv doesnt catch/recieve the frequency of the channels. i think your case is like this..
you have to change it .. its not very costly..
there was a problem in my LG tv that i was not recieving the Discovery channel freq. then i had to replace this part. now i can see it..

regards,,

Aug 07, 2008 | Projection Televisions

1 Answer

My PVR has retuned (DSO)to the wrong transmitter. I receive signals from the Winter Hill transmitter and live in SW Cumbria. My Humax 9200T has retuned ok but my older 8000T has retuned to a transmitter in...


Not a complete solution but after much fruitless fiddling through the menu I eventually found that the programmes were actually there but under different channel numbers.
I searched a long way down the LIST of channels (on remote) The BBC1 channel I want is now 800 BBC. Selecting 1 on the remote still brings up BBC Wales.
This applies to my Humax 8000T PVR - I can't comment on other makes of Freeview box.

Nov 05, 2009 | Projection Televisions

1 Answer

I need a remote control code for my nikkai a88jb freeview box so that I can programme a universal remote control. Any ideas?


my nikkai a88jb after connected still come up with "empty data base" . no signal of anything showing and i did plug in antenas! pls what shoul i do?

Apr 18, 2009 | Projection Televisions

1 Answer

I have a Wharfedale Digital Freeview Receiver LPDV832B, having set this up following the instructions provided it appears I am not receiving all the freeview channels available ie BBC1, please advise.


It is very possible that you require an aerial upgrade to receiver all the digital channels available, you should check with a local aerial installer.
SUPER8

Nov 16, 2008 | Projection Televisions

1 Answer

I have lost the normal tv channels on all 3 of my TV's (bbc 1 bbc 2 itv channel 4 through the aerial) but freeview channel are still working on AV. any ideas?


If you have all 3 tv's in the one house and on the one antenna then it sounds like you have been subject to either a lightning strike or a large static discharge onto your antenna. What this means is that the tuner packs in the back of the tv's has been damaged and will need to be replaced. However as you have said in your question they do work using an av input. This will be your cheapest option to get them working again. Buy cheap vcr's for them and connect via av cables, as the tuner modules are expensive to buy and even more so to have fitted.

Jul 02, 2008 | Projection Televisions

1 Answer

We have a sharp lcd tv c/w built freeview,the last couple of weeks it keeps losing just 1 channel ie bbc1 or itv1 every other channel is fine if we retune the tv everything goes back to normal, is it the...


no problem occur on your set but the only problem is you can not lock the fine tuning (in manual procedure) but is it better to set the program to AUTOSCAN OR AUTO PROGRAM and authomatically tune and save to the memory all the program channel

Apr 29, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

1,217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...