Question about Electrolux 18 in. ESL4114 Slim-Line Built-in Dishwasher

2 Answers

Dishlex dishwasher The dishwasher will not complete its cycle and has a flashing light on the normal wash indicator.

Posted by on

2 Answers

Re: Dishlex dishwasher

I have the same problem and the main conrol board was replaced. No Problems since.

Posted on Jun 11, 2007

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 3,130 Answers
Re: Dishlex dishwasher

Theres a problem with the water level sensor or the main electronic control PCB.

Posted on Apr 21, 2006

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Kenmore elite dishwasher model 630 Smart Wash light is flashing

You may want to try:
Press a series of four buttons in quick succession. Press "Heated Dry," "Normal Wash," "Heated Dry" and "Normal Wash" to instruct your Kenmore dishwasher to run a short diagnostic test.
Wait for two minutes while your Kenmore dishwasher runs its diagnostic test.
Press the "Cancel/Drain" button once your dishwasher has completed its diagnostic test. This should reset your dishwasher control panel.
Check to make sure that there's no standing water in the bottom of your dishwasher. Standing water in your dishwasher may indicate that your dishwasher has stopped mid-cycle. You will need to press the "Cancel/Drain" button before you can reset your dishwasher control panel.

Dec 18, 2013 | Dishwashers

1 Answer

Dishlex dishwasher won't complete a cycle. Number 60 shows up and a small flashing line. ??????

Drain pump is blocked. .If you are good with tools you can clean it yourself. Let me know

Mar 28, 2013 | Dishwashers

1 Answer

I have a Kenmore elite dishwasher M#665.13419k701, when you run the cycle it shuts off after about 10 seconds and the normal wash light blinks. what can i check??? Thanks. Israel

Hello, welcome to FixYa.

I understand by reading your post which indicates it is a Kenmore dishwasher you appear to have a concern with the cycle interuopting and the "normal" light flashing.

I'd suggest you first try entering a diagnostic/ do so is as follows. Press the following buttons in this sequence...


This diagnostic may take approx. 15-20 minutes to complete. Let it proceed through to completion and let me know what happens and we can go from there.


Macmarkus :)

Aug 19, 2011 | Kenmore Dishwashers

1 Answer

Want to disable the alarm

To Set the Cycle Completion Signal Tone Level
• With the "CLEAN" and "SANITIZED" and "RINSE AGENT" Indicator
Lights flashing.
• Press the "Tone Level.
• As you press the "Indicator Lights illuminating and the Cycle Completion Signal
Tone level changing.
o If none of the Wash Cycle Indicator Lights are illuminated,
there will be no tone. The Cycle Completion Signal is turned
o If one of the Wash Cycle Indicator Lights are illuminated,
there will be a low Cycle Completion Signal Tone Level.
o If two of the Wash Cycle Indicator Lights are illuminated,
there will be a medium Cycle Completion Signal Tone Level.
o If three of the Wash Cycle Indicator Lights are illuminated, you
will be at the maximum Cycle Completion Signal Tone Level.
• Press "START" to save your settings.

Dec 16, 2010 | Bosch SHX3AM05SS Stainless Steel 24 in....

1 Answer

Dishlex global 300.... The normal light starts flashing mid wash

i think it means the water heater in the dishwasher is not working,or the element is shot.
my 300 had a burning smell before the light started flashing.

Feb 07, 2010 | Electrolux Dishwashers

2 Answers

Hotpoint FDW60 flashing eco light

if the eco light is flashing, this indicates that saftey float switch has activated in the base of the dishwasher usually caused by a leak, a polystyrene float activates a microswitch which cuts of the water inlet supply

Mar 28, 2009 | Hotpoint 24 in. FDW60 Free-standing...

3 Answers

"HO" flashes on display during washing.

HO, indicates that the dishwasher is using Hot Water. It is completely normal.

Mar 08, 2009 | Frigidaire Professional Series 24 in....

1 Answer

Dishwasher flashes on Fast Wash

I am hoping I have just fixed mine with same problem. Couple weeks ago started stopping at start of cycle with fast button flashing. Check filters so one on top of unside machine and one on tap if you have one on there. Mine were blocked but still wouldnt work. I pulled out machine to find a kink in the water pipe. I have straightened this out and up to now its working. Fast button flashing refers to water inlet problem.

Feb 27, 2008 | Dishwashers

Not finding what you are looking for?
Electrolux 18 in. ESL4114 Slim-Line Built-in Dishwasher Logo

385 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electrolux Dishwashers Experts


Level 3 Expert

4342 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you an Electrolux Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides