Question about Philips Lands Phones

Open Question

Philips DECT 111 cordless telephones. When speaking for 20 minutes, phone line goes dead. Presumably supplied rechargarble batteries are no longer any good. Have tried to recharge them but problem still occurring. Will the batteries have to be replaced and is it necessary to replace with Philips ones. What mAh should i be buying?

Posted by on

5 Suggested Answers

  • 1 Answer

SOURCE: BATTERY REPLACEMENT FOR PANASONIC KX-TC1221BXB CORDLESS TELEPHONE

WENT TO A BATTERY SUPPLIER SITE IN UK

Posted on Apr 08, 2008


SOURCE: Thomson GE DECT 6.0 28213 Cordless Telephone

Another fix is to register the phone again. I do not have to de-register it first. Also, be patient. Sometimes when I take the handset from the base it searches for the base. If I push the talk button before it finishes searches, it beeps. Once it has found the base, it is ready to go. I have Verizon voice mail and it seems that when I have a message waiting it causes the phone to de-register.

Posted on Jul 20, 2008

  • 2 Answers

SOURCE: UNIDEN Powermax5.8 cordless phone charging

waaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa

Posted on Jul 30, 2008

  • 1 Answer

SOURCE: handset for ATT 5.8 GHz Cordless Telephone Model 5870

i have at & t 5870 cordless phone it is no t working. handset is dead i change the battery but still not working .please give some advice.

Posted on Dec 17, 2008

  • 7993 Answers

SOURCE: info to change message

Recording a Personal Greeting
Your answering system comes with a pre-recorded outgoing message or greeting that plays when you receive a call: “Hello, no one is available to take your call. Please leave a message after the tone.”
You can record your own personal outgoing greeting. Your recorded greeting must be between two seconds and thirty seconds long.

  1. Press /mute. The system announces the number of new and old messages, then starts to play themessages unless it has no messages.
  2. Press 5 to stop the announcements or message playback. You will hear intermittent beeps indicating that thesystem is in the command waiting mode.
  3. Press 8 to start the recording. The system announces, “Record greeting.” Begin recording after the announcement.
  4. When you finish recording, press 8 again or press 5. You will hear a confirmation tone, and your recordedgreeting plays back for you.
Selecting a Greeting
Once you have recorded a personal greeting, the phone automatically switches to your personal greeting. You can also switch back and forth between the pre-recorded greeting and your own greeting at any time.

  1. Press the /mute. The system announces the number of new and old messages, then starts to play the messages unless it has no messages.
  2. Press 5 to stop the announcements or message playback. You will hear intermittent beeps indicating that the system is in the command waiting mode.
  3. Press 6. The system plays the current greeting.

Posted on Jan 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Distorted sound on uniden dect.6.0 cordless phone


it could that the battery is not keeping a charge. or the land line is bad. change battery first. sometimes new batterys are bad.

Mar 27, 2017 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

How long do the batteries last


If the batteries are 3 years old it's time for new ones. Talk time when new is only about 6 hrs.

Sep 24, 2014 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

The DECT telephone is linked to our mainline phone - however it does not pick up the dialling tone or the ring tone. The battery is okay, the signal is good, but you cannot speak on the phone. ...


Re-Register a Handset to the Base
1. Remove Handset Battery.
2. Reconnect battery while holding down "*" and "#" key.
3. Then press the right upper key under the LCD.
4. Press the "End" key.
5. Wait a few seconds and then the phone will be ready to register to the base.

Mar 09, 2011 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

My phone says check Tel Line


Sounds like your telephone line might be dead. If you have a gray or tan telephone box on the outside of your house you can plug your phone in there to test the line. If you get dialtone then thrers a problem in your house wiring, if you don't get dial tone then the line is dead and you need to conact your telco provider.

Apr 14, 2010 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

How do I set up Philips DECT 215 To Show number calling


You need to subscribe to a caller display service with your telephone provider. e.g. if your phone line rental is with BT, contact the phone number on your bill for customer service and request them to activate caller display. There will normally be a small monthly charge payable for this service.

Nov 12, 2009 | Philips DECT 2151 Cordless Phone

1 Answer

Philips dect 521/525 - 3 year old phone - No dialling tone on one handset


I had the same problem and my hubby managed to reset the phone by simply unplugging it from the electical network. Just wait for few minutes (the date goes back to 1 Jan 2005), then plug it again and try to dial a number. It should work.

Oct 05, 2008 | Philips DECT 2151 Cordless Phone

1 Answer

GE MODEL 28112 DECT 6.0 CORDLESS PHONE


I contacted GE today and they told me how to get the caller ID to work on the additional handsets. You must follow these steps in the exact order given.

#1 - unplug the base phone
#2 - unplug the telephone line from the base phone
#3 - remove the battery packs from the phones
#4 - wait 10 minutes.

reverse the order when assembling. Put battery packs in phones, put the telephone line back in the base phone and lastly plug all phones back in. It takes about another 10 minutes after that before all phones start recognizing caller ID but it now works fine.

Mar 26, 2008 | GE 28112 Trio Cordless Phone

2 Answers

Caller ID Problem on the GE2811 Twin cordless phone system


How to get the caller ID to work on the additional GE DECT phone handsets. You must follow these steps in the exact order :
#1 - unplug the base phone
#2 - unplug the telephone line from the base phone
#3 - remove the battery packs from the phones
#4 - wait 10 minutes. reverse the order when assembling. Put battery packs in phones, put the telephone line back in the base phone and lastly plug all phones back in.
It takes about another 10 minutes after that before all phone handsets start recognizing caller ID.

Oct 23, 2007 | GE 28111 Cordless Phone

Not finding what you are looking for?
Lands Phones Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Lands Phones Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18386 Answers

kakima

Level 3 Expert

102366 Answers

Cindy Wells

Level 3 Expert

4989 Answers

Are you a Philips Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...