Question about Kenwood Car Audio & Video

1 Answer

How to wire a kenwood kdc d300 - Kenwood Car Audio & Video

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 42 Answers

All components on your Amplifier should be labled. Ground Will go to any ground on your Vehicle Ex. A bolt under your trunk floor cover. Power has to be ran from your positive terminal onto your batter and throught the interior of your car to your amps 12v +. The MEMORY TERMINAL IS NEEDED FOR FUNCION! It will be between Ground and POWER or NEXT TO POWER.. This has to be ran to your cd players BLUE MEMORY wire or you can bypass it directly to the POWER, WARNING!!! if you use the bypass method, put a switch that you can pick up from any autozone or such between the two points to shut off the amp, other wise it will run constatly and kill your battery. The two RCA's have to be plugged into the back of your cd player and ran back to your amp and plugged into the Primary Slot (red-white) and finnaly the +.- speaker wires need to be ran to your subwoofers. Once all conected pop in a cd, adjust your cd players bass settings and also adjust your lows, mids, and highs on the amp to fine tune your speakers. IF you are looking to maximize your speaker wattage, you can use the bridge teqnuiqe. But beware you are going to doubble the ammount of power into each speaker. Take both positives, or if only one speaker just the single possitive, and place it into the Right SPEAKER insert on the Amp, and take both negitives and place it into the LEFT SPEAKER insert, and run the wires like normal to each speaker, 1 wire per - one wire per positive, in doing so both speakers run using maximized power usage

Posted on Sep 11, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What color is the wire for the subwoofer on the Kenwood KDC-400U


The sub-woofer isn't connected to the wiring harness of the KDC-400U. It has to be wired separately. Then the sub-woofer input gets connected to the KDC-400U sub-woofer out using R/L audio wires as show on page 13 of the Quick Start Guide. The direct link to the Quick Start Guide is http://manual.kenwood.com/files/4fd9a24acb9fa.pdf . You may be able to use the wiring information on pages 12-13 to help you determine which wires aren't going to the sub-woofer.

Most Kenwood Car audio manuals are available here: http://manual.kenwood.com/en_contents/search/ .

I wish that I could give you more information.

Cindy Wells

Apr 28, 2017 | Kenwood Car Audio & Video

1 Answer

Car stereo installion


I think you left the yellow wire from the kenwood disconnected

Mar 05, 2013 | Kenwood KDC-BT752HD CD receiver

1 Answer

I am installing kenwood kdc-mp443u. it is flashing protect and i can't remove it. can you help please?


A speaker wire has a short-circuit, crossed, or touches the chassis of the vehicle it activates the protection mode function.
? Wire or insulate the speaker cable properly and press the reset button. If the "PROTECT" code does not disappear, consult your nearest service center.
I have attached a link for you which is for a free Kenwood KDC-MP443U instruction manual download. Nice receiver by the way!
Kenwood KDC MP443U Instruction Manual

Dec 18, 2010 | Kenwood KDC-135 CD Player

1 Answer

How to install a kenwood kdc-135 car stereo


This is a link to Kenwood for your KDC-135 Owners Manual. Page 15 has the wiring diagram and pages 16 and 17 cover physically installing the unit.
http://www.kenwoodusa.com/UserFiles/File/Global/Consumer/Manuals/KDC-135.pdf

Nov 17, 2009 | Kenwood KDC-135 CD Player

2 Answers

Need a wiring diagram please


wiring diagram or colour code for kenwood cd player model kdc-5108

Nov 16, 2009 | Kenwood KDC-W3534A CD Player

1 Answer

Need to know what the wiring diagram for kdc-x789


well if you mean how to wire it up to ur car buy a radio adapter from best buy and color match all wires

Aug 31, 2009 | Kenwood Excelon KDC-X789 CD Player

1 Answer

Wires


http://inform3.kenwoodusa.com/manuals/kdc-s3007.pdf

download the manual here from the kenwood service site.
Page 16 of the manual has the color codes for the wires.

Dec 22, 2008 | Kenwood KDC-S3007

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4915 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

78267 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...