Question about Star Logic 17" LCD Monitor

1 Answer

Monitor flashes then goes blank

I have just recently attempted to update to service pack 3 which seemed to cause my computer to crash. After much to-do and many hours on the phone, we came to realize that only my monitor wasn't working. When I plugged my old, small flat screen monitor into the cpu I had no problems. The monitor is a starlogic and I've had it for about 4 years. I recall returning the monitor a couple of times because I had problems getting it to work with the settings that I already had on my computer. It seems that I had to adjust the refresh rate or something. Do you have any suggestions? My issue may be more difficult to fix but I thought I would check.

Posted by on

  • datdud89909 Oct 21, 2008

    the monitor comes on and the goes blank after a few minutes

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

As i told somebody in another post, try to find a driver for this monitor. If it came with a disk try to get it from there otherwise the internet is a easy place to find this. What could've happened is when you installed servicepack 3, which is known for causing many problems, it may have deleted the driver that supported this monitor, even if the driver may have come already on the computer. This is only one of many solutions of which you can try. Hope it helps :)

Posted on Sep 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Kds K-92bw After about 5 min the screen goes blank..turning the unit off than back on the screen looks great for a while about 3 min than goes black..seems to be a caused by heat


This issue is most likely caused by a capasitor doing bad. There is no easy fix. It must be disembled and the power supply repaired. If done properly, it should cost somewhere between $ 50 to $125. But it may do it again as the Pwoer supply is a known issue for this monitor. Sorry.

Sep 21, 2011 | KDS K717s 17" LCD Monitor

1 Answer

SyncMaster2220wm LCD, 3 years old, and 3 weeks. Display flashes on, then goes to black screen.


The problem is in the power supply inverter board caused by bad capacitors and poor solder connections, an attempt can be made to repair or replace the board, If a professional gets involved it will be pricey.

Apr 26, 2011 | Samsung SyncMaster 2220WM 22" LCD Monitor

1 Answer

Screen going blank on system boot and on switch off/on


Hello,

It is the picture picture board on your monitor that is malfunctioning, since the power led or button is on, but the display screen goes blank after a fraction of seconds, it means the picture board of your monitor has developed fault.

The best thing for you to do now is to take the monitor to a local repairer within your vicinity or any service center to help with the replacement of the picture board because the fault is not something you can fix yourself, in order not to complicate issues.

Take care.

May 08, 2010 | Sony SDM-HS75 17" LCD Monitor

3 Answers

My monitor went black, and the power switch just flashes.


is your CPU working properly? if that the case, your monitor is in need of a service.
reasons for why a monitor goes blank?
Reason 1: Wetness
The number one reason why computer monitors go blank is - wetness. Believe it or not, when your computer monitor is exposed to humid air, sometimes water can condense and accumulate in the monitor. This causes the monitor to malfunction and go blank. I've had this happen to my desktop PC at least three times before. What you need to do is to leave the monitor alone for some time and allow the water to evaporate. That usually solves the problem.

Reason 2: Faulty Graphics Card
The next reason why your computer monitor goes black is due to a faulty graphics card. The best way to detect this kind of problem is to connect up a new monitor to your PC, then check if you have a blank screen. If you continue to have a blank screen, then it's likely your video card is faulty.

Reason 3: Faulty RAM
This one is less obvious and less common, but it can happen. You might sometimes get bad RAM modules which prevent your PC from booting up even to the basic BIOS startup screen. To detect this kind of problem is more troublesome, you might need to remove those RAM modules and insert them into another computer.

Reason 4: Loose Connections
Another reason why your monitor goes blank is due to loose connections. The connection from the monitor to the mains is usually a culprit, as is the connection between the monitor and the video card. Check those connections before you declare your computer monitor as faulty.

Reason 5: A Short Circuit In The Motherboard
And the final reason why your computer monitor goes blank? It's possibly because of a short circuit in the motherboard. This is the most undesirable outcome of course, as you might have to replace your entire motherboard. However, it's possible that this can happen - so keep your fingers crossed and hope it doesn't happen to you.
try this.
please rate my solution.
have a nice day.

Jul 05, 2009 | Dell E152FP 15" Flat Panel LCD Monitor

1 Answer

My monitor AOC 912Sw-4 does not turn on. Power button`s led is flashing all the time.At the beginning I waited some minutes and I could use it normally, but right now it is impossible see any image on it.


only choice is to give the monitor for service.
anyway read this, this help you.
is your CPU working properly? if that the case, your monitor is in need of a service.
reasons for why a monitor goes blank?
Reason 1: Wetness
The number one reason why computer monitors go blank is - wetness. Believe it or not, when your computer monitor is exposed to humid air, sometimes water can condense and accumulate in the monitor. This causes the monitor to malfunction and go blank. I've had this happen to my desktop PC at least three times before. What you need to do is to leave the monitor alone for some time and allow the water to evaporate. That usually solves the problem.

Reason 2: Faulty Graphics Card
The next reason why your computer monitor goes black is due to a faulty graphics card. The best way to detect this kind of problem is to connect up a new monitor to your PC, then check if you have a blank screen. If you continue to have a blank screen, then it's likely your video card is faulty.

Reason 3: Faulty RAM
This one is less obvious and less common, but it can happen. You might sometimes get bad RAM modules which prevent your PC from booting up even to the basic BIOS startup screen. To detect this kind of problem is more troublesome, you might need to remove those RAM modules and insert them into another computer.

Reason 4: Loose Connections
Another reason why your monitor goes blank is due to loose connections. The connection from the monitor to the mains is usually a culprit, as is the connection between the monitor and the video card. Check those connections before you declare your computer monitor as faulty.

Reason 5: A Short Circuit In The Motherboard
And the final reason why your computer monitor goes blank? It's possibly because of a short circuit in the motherboard. This is the most undesirable outcome of course, as you might have to replace your entire motherboard. However, it's possible that this can happen - so keep your fingers crossed and hope it doesn't happen to you.
try this.
please rate my solution.
have a nice day.

Jul 05, 2009 | AOC 912SW-4 Monitor

1 Answer

Viewsonic VX912 Distorted screen


for meantime use the previous monitor suitable to your pc then download the files you need enabling the new monitor to work.

Oct 15, 2008 | ViewSonic VX910 19" LCD Monitor

2 Answers

Monitor won't turn on -- flashes on then off again


Hi...there,

Well...you can kicks and screams all you like. It's won't help... It's seems your inverter busted, need to replaced a new ones. Have funs!

Sep 29, 2008 | LG Flatron 295LM 22" LCD Monitor

1 Answer

LCD monitor goes blank


It appears that the display resolution set in your display properties is out of the range that the LCD can display.

Try this.

Boot to the ENABLE VGA MODE by pressing F8 to get the Windows Boot Menu. If you can get to the desktop, then go to display properties, and see if you can change the resolution to higher settings and maintain video. (If the video blanks out, then it should revert to the previous setting in 15 seconds)

Aug 03, 2008 | Gateway FPD2275W LCD Monitor

Not finding what you are looking for?
Star Logic 17" LCD Monitor Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Star Logic Computer Monitors Experts

scj103

Level 2 Expert

80 Answers

Geoff

Level 3 Expert

413 Answers

Fernando Torres
Fernando Torres

Level 2 Expert

69 Answers

Are you a Star Logic Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...