Question about JVC Audio & Video Receivers

Open Question

JVC XL-M401 6-disc CD player just quit working. It doesn't respond to the cleaner disc for CD players that I tried. Any thoughts?

Posted by on

4 Suggested Answers

  • 1 Answer

SOURCE: Sony Compact Disc Player (CDX-L380/

Sony Technical Advice say to try pressing the 'Reset' button - or else contacting a repair agent.

Posted on Jul 31, 2008

  • 1348 Answers

SOURCE: Yamaha RX-770 Receiver display quit

there is a bulb inside the backlight on the lcd display.it is 12 volt and alot of manufacturers run it from the +- 15 volt preamp power supply,on the plus rail.when the bulb burns out it can activate the dc speaker protect,or some other 12 or 15 volt circuit..if it is a flourescent display that is a different problem.those run on 5 12 18 and -32 volts.there is also a 6 volt ac filament voltage.you need the schematic.

Posted on Jun 14, 2009

ifix2
  • 11 Answers

SOURCE: how do i get the

m-error means mechanical error, it is caused by faulty gear and lever assemblies under the cd loading carousel . it is very hard to get to those so i do not recommend this repair to be attempted by non-technicians. i fixed lots of them, it was the most common problem in those units
www.ifix2.com

Posted on Sep 02, 2009

  • 1 Answer

SOURCE: hi I have a jvc

I had the same problem. Out of the blue, neither the single tray nor the cassette would eject. On top of that, it wouldn't change discs or even play the disc in the engaged tray. I then unplugged the unit, moved it to my work table, plugged it back it, and it worked fine.
Last year I had a similar problem with the JVC receiver RX750V that I had bought along with the CD player, probably around 1986--it simply would not turn on. I took it out of the cabinet, and shipped it to a JVC repair shop called BC Electronics, Levittown, PA 215 547-7600. They were very knowledgeable and courteous, but said they could find nothing wrong with the unit, and that the unit worked fine. They shipped it back, and the unit worked fine initially. I found that the problem recurred, i.e. that every so often I'd turn the machine on via the on-off switch, and nothing would happen. If I then unplugged the unit, left it off for a while, and plugged it back in, it would work fine. I then installed an in-line on-off switch on the receiver cord. It now seems to work fine consistently.
It seems that after twenty years, this same problem may affect this generation of JVC components, i.e. that the main power source to the unit must occasionally be cut off.
On the other hand I could be completely wrong and just plain lucky...Hope that helps.

Posted on Feb 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a sherwood cdc-5090/c/r multiple cd player - it goes on error when using open/close, disc selector, disc skip. have tried troubleshing guide but doesn't seem to work.


The problem is in the CD loading bays, quite often the gears will ware over a period of time causing error messages because it is unable to complete the cycle. The second issue is the timing gears go out of sink because one of the CD'S gets jammed against the other causing it go out. The repairs are tricky because of the timing issue, however if gears are stripped the whole CD bay must be replaced.

Mar 10, 2012 | Audio & Video Receivers

1 Answer

When I put a cd in my jvc cd player it reads no disc - the radio on the player works


This is usually cased because the unit is sensing that your spindle motor is not turning or turning at a slower speed then normal. "The spindle motor is the motor that spins the disc. This is the most common problem found in DVD and CD players.

Aug 24, 2011 | Audio & Video Receivers

1 Answer

I have a Teac AG-780. The Radio works, good sound out of two Bose 901. But when I click on the CD button and play my CD palyer (JVC XL-R5020) it doesn't sound. BUT! I place a Head Phone jack in it, the...


So what are we dealing with - the CD player or the Receiver?

901 involvement implies you have an Active Equalizer somewhere in the audio path. IT has buttons on it that can interrupt the signal.

What's connected where, exactly?

Jul 14, 2011 | Teac Audio & Video Receivers

2 Answers

How to unlock the disc tray on my JVC compact component system MX-KB30


If your CD player dose not respond to normal commands, there is a problem with mechanism. Have serviced

May 10, 2008 | Audio & Video Receivers

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Audio & Video Receivers Experts

 Elex
Elex

Level 2 Expert

49 Answers

Cindy Wells

Level 3 Expert

4757 Answers

Rod
Rod

Level 2 Expert

224 Answers

Are you a JVC Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...