Question about Dishwashers

1 Answer

Calypso washer display "FD" perhaps meand full drain and can't reset and just stop. I run washer with back cover out to see that while water doesn't fill up the drum but normally agitates and just fill up the water reservoir to full and don't drain out to sewer and washer just stops with the message "FD"

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 166 Answers

Peace broohilda,
ngafm At your service!

With an error code the only way to find and to repair this is,

First unplug the washer and wait a few minutes then restart it like rebooting your computer when its acting strange!
If it corrects the problem GREAT!!! WE WIN!


If not only a trained laundry tech can make the electronic diagnoses.
Like we used to be able to fix my own cars, but not today they need diagnostic equipment!


How old is the washer?

If the appliance is 10 years old or more you it may not be advisable to put good money into bad!
New appliances are so much more efficient today that they can save you a lot of money in energy!!!!
Water,Electric and detergent! And put money back in your pocket!
The new appliance will pay for itself in only a few years!


You will be fine
Bless You ngafm
PLEASE GIVE ME A GOOD RATING HERE AT FIXYA.COM BEFORE YOU SIGN OFF!!!!!!!!!!!!!!!!!

Posted on Sep 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

GE DISHWASHER PDW7300N10WW DISPLAY SHOWS RANDOM CODES AND BEEPS CONSTANTLY.


old post. but I am posting here, to help , searchers.
this model has a full computer behind that panel
with service modes and factory test modes.
and a service manual..
try cycling power, (pull main power plug for 5min.)
make sure the drain line is not blocked. (i use a 5 gallon bucket to test my washer drain hose. 2 person, one to hold the hose firmly in his hands , aimed at buck. (the resest button kills all actions)

the beeps are error warnings, covered in the manuals.
there are many beep modes.
even door left open, does that, soap dispenser (option) empty.
the first tests on a PDW, washers, is the rinse, only mode.

when started, it first pumps the sump dry. (old water ejected)
if the pump do dose not start, but humms.. the drain is blocked.
then does a full rinse run. if not make sure the water valves are on.
these models have a Service mode, and a factory test mode
both are covered in the service manual, and allows the manual
testing of each mode and device in the washer.
The turbity sensor can get limed up , so run 1/2 cup of vinegar
in rinse mode. once running.


GE does not offer the serv. manual to DIY, but google does find them, if you search long and hard. "for sure"

is is a generic help page, but do not down load his helper browser bad (jeckle and hyde site) the HTML pages are safe.

http://www.appliancerepair.net/ge-dishwasher-repair.html

Aug 23, 2013 | GE Dishwashers

1 Answer

GE Dish Washer GSD 2800 DO3 runs a partial cycle...(even empty) and then beep and gives a message on control panel "washer arm blocked". Even ran without dish rack in washer still got the...


the rotating arm has a magnet in it to let the controls know if it is turning. Yours is not turning so
  • check the jets for blockages... you might have to remove the arm to clean them properly
  • make sure there in nothing stopping the arm from turning...spin the arm manually to see if it rotates freely.
  • knives etc sticking upward can stop the arms from rotating on the top rack
  • if you run without the rack the arm will obviously be not telling the electronic it is not blocked because it is not there. the rack must be in the machine with the magnet and the magnet passing correct messages.
  • If there is really no blockage then there is a elect fault that need to be sorted professionally.
  • PS have you taken the arm off anf squirted a hose up the inlet to see if water comes out all of the jets????

Mar 01, 2011 | Dishwashers

1 Answer

LG WASHER STOPS BEFORE THE END OF THE CYCLE..OE IS THE ERROR MESSAGE ON THE SCEEN


Hello & Welcome to FixYa

OE is a drain error and is displayed when the washer is unable to drain water. Please check the drain hose and drain pump filter for any clogs to clean the error. Please get back to me if you have any other questions.

Kevin

Feb 04, 2011 | Dishwashers

1 Answer

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off...


by the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store

Dec 29, 2010 | Frigidaire 24 in. FDB1050RE Built-in...

2 Answers

The machine is just flashing E24 on the front. What does this mean?


E24 = draining failure

If the appliance has stopped full of water then you have to check the drain hose for blockages, especially where it connects to the drain. Check the pump for a blockage, bail out the water manually and remove the filters. You should find a cover held by a screw covering the pump impeller. Take out the screw, take off the cover and remove anything jamming the pump. Refit the cover and try the appliance again.

Sep 06, 2010 | Dishwashers

2 Answers

Will not drain all the way down at end of cycle


What you could do is take the drain hose off under the sink and get a 5gallon bucket and run a cycle and see if it drains at all. If it doesn't drain that would lead to the pump being bad. If it drains agallon or so and stops and you still have water in the bottom then it possible there could be something wrong with the timer.

Jan 07, 2010 | Dishwashers

1 Answer

What is causing the drain pump to continue running


C1 - Partially Blocked Drain - This error will occur when dishwasher was unable to pump out water in less than 95 seconds. Check drain line for debris and blockage. If clear, check for a restricted drain valve in the pump. Check the pressure sensor for correct operation as it sounds like it may be defective and thinks that the machine is still full of water after it has emptied.

Oct 30, 2009 | Dishwashers

1 Answer

Water will not drain in whirlpool dishwasher


If you experience a problem where the washer does not drain properly or the drain pump makes excessive noise, here's the information you need to check the drain pump:

Symptom: PUMP IS RUNNING, BUT NOT DRAINING PROPERLY.

1. Unplug the washer while servicing inside the unit.
2. Remove the lower kick panel under the door by removing the three 7mm screws under the bottom edge of the panel. HINT: Use a couple of blocks of wood to prop up the front feet of the washer to gain better access to the screws. Once the screws are removed the panel should drop down, and then pull off. If the panel becomes stuck, a slight tap on either side will dislodge it.
3. Locate the drain pump. It will be located directly under the wash tub (it is the only pump this washer has).
4. There is an access removal cover on the pump that can be removed to clean out the trap. BEFORE doing this, it is strongly recommended that you remove all residual water from the wash tub & drain line or you will have about a gallon or so inside your washer and on the floor to clean up.
5. Here's a helpful way of quickly removing the residual water. If you own a wet/dry shop vac, remove the drain hose from the standpipe at the wall and pull a vacuum with the shop vac. This will empty the wash tub, pump and drain lines. If you don't own a shop vac, grab a bunch of old towels and open the access on the pump slowly so that it comes out at a trickle. Allow the towels to soak up the majority of the water. Close the access and stop the water if you need to get additional towels.
6. Open the pump access and remove once you have all the water drained. Check the drain pump for foreign objects and debris. Check the pump impeller and make sure there's nothing caught in it. Items as small as toothpicks or cotton swabs have been known to stop this pump from working.
7. Clean out the pump thoroughly and reinstall the access cover. Make sure the cover is snug, but do not over tighten.
8. Place the drain hose back in the standpipe (IMPORTANT - DO NOT FORGET!).
9. With the bottom panel still off, plug the washer back in and select the following on the operator console - DRAIN SPIN, NO SPIN, and then press any button under OPTIONS 4 times (it must be the same button). "C00" will show on the console display as the washer begins diagnostics mode.
10. Check the drain pump for leaks as the washer fills. The pump is gravity filled and will hold water even it is not pumping. Allow washer to run through diagnostics until it begins the wash tub tumble cycle.
11. At this point, you can stop the diagnostics procedure by pressing PAUSE/CANCEL 2 times. The drain pump energizes and the washer will begin to drain.
12. If the drain pump works normal and there are no leaks detected, reinstall the bottom panel and tighten screws.


NOTE: It is normal to have residual water left inside the wash tub under the wash basket. This is why it is important to leave the door ajar when not in use so this water does not become sour.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 20, 2009 | Whirlpool 24 in. ADP5962 Free-standing...

1 Answer

Hotpoint BF162............. Water left, not draining


Open the bottom panel of the washer and see if it is full of water, if it is drain it away and clean all of the filters inside the washer and reset.

Mar 04, 2009 | Hotpoint 23 in. BFI62 Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Brad Brown

Level 3 Expert

13732 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...