Question about Hotpoint Aquarius WD640 Front Load Washer/Dryer

2 Answers

Error code f13

How do i repair this fault

Posted by on

  • 1 more comment 
  • swats11 Sep 28, 2008

    everytime i switch dryer on,it works for some time and then cuts power of my whole flat and f-13 error is seen on screen which cannot be stopped for some time and it does not complete drying cycle and does not allow us to switch m/c off.

    even if we try it comes on again and trips power off everytime we try.my washer/dryer is not even 1 yr old.pls suggest sol

  • Anonymous Feb 10, 2009

    I have same prob goin to phone hotpoint. Apparently the thermostat is gone it happens all the time according to online forums

  • samkebab Feb 23, 2009

    I have an f13 fault.. can anyone recommend how to fix this?

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 206 Answers

There is a small thermostat button ontop of the Heater mechanism which has tripped . It has either a red dot or blue dot ontop. Use a pin or opened up paper clip and push through the red wax. It will go click and it is reset. .
It sometimes trips out with a F code which normally trips the machine off because it thinks the Heater unit is on fire.
There is a small disk which costs about £15 to buy which you can change. You will need HEX screwdriver set to change and open up the Heater matrisx to clean the fluff off the element.

error code f13 - 318c857c-2bc5-40ec-ab21-f6fe52de17a6.jpg





Posted on Nov 15, 2014

Can't comment on tripping your power but see posts on this sight for Hotpoint WD860 for F-13 solutions.

...also if it's less than a year old then you're still in the warranty period I believe. Perhaps you can get Hotpoint to fix this?

Posted on Oct 17, 2008

1 Suggested Answer

  • 1294 Answers

SOURCE: machine fault code "f13"

Plug off the wall. There is a thin rubber tube going from the switch area to the exit near the outlet tube. Probably this is blocked. This tube should be free from any blockage; take out the top clip from this tube and blow into it - it should be free, clear the blockage if any and refit. This is the water level tube which tells the machine when to switch off water, etc.....

Posted on Sep 03, 2007

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F13 fault showing on my Ariston margarita 2000 awd12 washer dryer and the control Knob keeps continuing to turn endlessly. What could be the problem. Yours desperately John Russell


From memory I think this is a dryer temp. sensor error. Check youtube out with query; "Wash Machine F13 error code". A company in England, eSpares, posts a few vids to help. I've bought a few things from them, very helpful and good prices. I have no connection with eSpares, accept an occasional customer. If you can do it yourself it is a quick, inexpensive fix. Good luck.
H

Apr 03, 2016 | Washing Machines

1 Answer

I have a hotpoint ultima wf860 it was all fine then all of a sudden its saying the error code f-18 how can I fix this please as I havent enough money for a newone yet. many thanks x


Hi, The link below is a user manual for a hotpoint ultima wf860 and below that are the error codes, I wish you all the best......CHEERS...

file:///C:/Users/Steve/Desktop/4992cbf9-f956-4127-bdab-caa958e02377.pdf <---"NEED TO COPY AND PASTE"

Hotpoint Washer Error CodesF01 - Electronic circuit board fault
F02 - Motor circuit fault
F03 - Temperature sensing fault
F05 - Waste pipe blockage or pump issue
F06 - Door lock fault
F07 - Electronic circuit board fault / heating circuit fault
F08 - Heater fault
F09 - Software fault
F11 - Pump circuit fault
F12 - Electronic control fault
F13 - Dryer temperature sensing fault (washer dryers only)
F15 - Heater control fault (washing machines and washer dryers)
F16 - Drum lock position sensor fault (top loading machines only)
F18 - Internal data error
F19 - Fan motor or heating fault (washer dryers only)

Apr 01, 2016 | Hotpoint Washing Machines

1 Answer

Washer was working.. electicity whet out... when emergency generator came in.. door lock message.. nothin I do works


Why is the "F dl" light come on - Kenmore Elite HE3 ...

https://www.ifixit.com/.../Why+is+the+%22F+dl%22+light+come+o...

iFixitThese are the errors for error code F/dL Door Lock Error Condition A Door Lock ... orrepair the following Door Lock Mechanism broken or removed from the Door ... these are usually indications of a failed door latch assembly and will require replacement. ...FdL code would not reset until I turned washer on to start load.

Troubleshooting - Support - Dexter Laundry

www.dexter.com/support/troubleshooting/
Dexter Washer Troubleshooting. Select your problem form the following list to reveal a list of possible solutions and supporting documentation. Constant ... F1 / Door Lock Error Door failed to lock properly. + ... Error Code F13, F15, F17, F19 +.

Washing Machine Fault Codes « Tips, Tricks & Recipes

www.appliancefactoryparts.com/blog/.../washing-machine-fault-codes/
Feb 20, 2010 - Failure Code, Condition, Check/Repair. "F1?, Water ... "F7?, Door lockrelease fault, ?· Bent pull-rod for door latch. ?· Bad door latch ... Water overflow error, Water supply does not stop after sensing an overflow condition. Turn off household water supply to washer and unplug power cord. ?· Check wiring ...

Why won't the door open on my Kenmore front-loading ...


Dec 10, 2015 | Washing Machines

1 Answer

F13 and F11 codes pop up


F13 is
Dispenser Circuit Error
If the dispenser motor is not able to be driven to it's proper position.
Check mechanical linkage from dispenser motor to the top of the dispenser
Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU)
Check Dispenser Motor

i snagged this answer from another site
i think its a worn bit of plastic
as it becomes britten when not always wet
much like a boat out of water

Mar 05, 2015 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

1 Answer

I have a F13 fault that wont reset on a AWOE9759. I do not know what a F13 fault is but i have tried what it says to do in the manual. Please help.


F13 Error = Dispenser circuit error
If the dispenser motor is not able to be driven to it's proper position.

Potential Causes

• Check mechanical linkage from dispenser motor to the top of the dispenser.
• Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU)
• Check Dispenser Motor

Replace failed component.

Dec 26, 2010 | Whirlpool Washing Machines

3 Answers

I have error code f13, can you help, please..


This s is how i fixed the F-13 Fault on my Hotpoint WD 640 washer dyer. Simple to fix just see the pictures and explanation. Hope this clears things up
Boxie


1_7_2013_12_28_59_am.jpg1_7_2013_12_29_33_am.jpg1_7_2013_12_31_38_am.jpg1_7_2013_12_31_56_am.jpg

Aug 07, 2010 | Dyson Memory CRO1 Front Load Washer

2 Answers

My AWOE8748 had a fault code F13. It has now switched itself completely off.


Hi,

F13 indicates "Dispenser Circuit Error" in your washer.If the dispenser motor is not able to be driven to it's proper position this error code appears.Check mechanical linkage from dispenser motor to the top of the dispenser. The wire harness connections to the dispenser motor and Central Control Unit (CCU) would have been faulty so check for those.Also do a final check on dispenser motor.


Thank you !!

Jun 20, 2010 | Whirlpool AWOE8748 Front Load Washer

2 Answers

My whirlpool washing machine keeps saying f13 whats wrong and how do i fix it


Hello, the F13 means "Dispenser Circuit Error", if the dispenser motor is not able to be driven to its proper position.
Check the following:
1. Check mechanical linkage from dispenser motor to the top of the dispenser.
2. Check wire harness connection to the dispenser motor and Central Control Unit and lastly
3. Check dispenser motor.
Thanks

Jun 10, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Machine fault code "f13"


Plug off the wall. There is a thin rubber tube going from the switch area to the exit near the outlet tube. Probably this is blocked. This tube should be free from any blockage; take out the top clip from this tube and blow into it - it should be free, clear the blockage if any and refit. This is the water level tube which tells the machine when to switch off water, etc.....

Sep 02, 2007 | Hotpoint Aquarius WD640 Front Load...

Not finding what you are looking for?
Hotpoint Aquarius WD640 Front Load Washer/Dryer Logo

1,132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...