Question about Xerox WorkCentre PE16 All-In-One Laser Printer

1 Answer

Xerox WC 16 - Did not start after power down

I had powered it down and when I restarted it - nothing comes up - plain dead. Tried re-seatting the connectors per one of the posts in here. Didn't work. Both the fuse on the power panel look intact.
When I power it up - there is no life in printer nothing at all... clueless and need to make it working again asap.
Thanks.

Posted by on

  • N S Sep 10, 2008

    Thanks - where do I get the power supply - I assume I need to change that entire board?



  • wmckennaimr Nov 16, 2008

    PE16 work centre stays "warming up"

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,072 Answers

That is a bad Lovw Voltage power supply.
I think it is $100, You have to replace it from teh bottom, it is up under the paper feeder.
There are a couple of fuses on it, But I have never seen one blow, just something goes bad in the power supply.

Posted on Sep 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code 116 330 workcentre 5330. already several times tried power ON OFF. but still same error is coming...


This code is HDD fail. You may be able to reformat by holding down stop, start and 4 keys and turning on power. failing this try stop,start and 6

Feb 14, 2015 | Xerox Workcentre 5330/p 5330 Mono Advanced...

4 Answers

Error code 117-363 printer starts machine is awake


only see error code 117-363 and not permited other option

Nov 26, 2009 | Xerox 6180MFP/N Printer

1 Answer

My xerox phaser 8500 will not turn on at all. I've tried restarting it, replugging it (in several different outlets) and it won't start up. It was working this morning and all of it sudden it just died. ...


If the printer is "dead" with no fans working then you might want to switch the power supply on the back. It has four or five silver screws. Then remove the inkloader from the top of the printer , and under the inkloader there are two more screw that hold the power supply and don't foreget to remove the cables I think it is a gray one and two white ones.These cables are connected to the top of the power supply. Then remove the right side cover, under the the power supply fan disconnect the 3 cables and the power supply should come out with no problem.
You might want to call www.iteminconline.com (800)367-4836, (703)971-5700 for extra support this guys are good. They well tell you exactly your problem if the solution that I gave you does not work.

Aug 06, 2009 | Xerox Phaser 8500/DN Printer

1 Answer

Powering Up My Xerox Phaser 8200DP


I assume no codes are coming up after leaving it on for a long time.
Most likely problem is the electronics module.
With the price of it you could buy 2 new dry ink phaser printers.
But what you are describing sounds like an electronics module issue.

May 27, 2009 | Xerox Phaser 8200DP Thermal Printer

1 Answer

STARTING PRINTER menu error


Have you tried turning it off, then when powering up again hold down the red clear button until you hear the printer start it's warm up cycle. I hope this helps!

Apr 16, 2009 | Xerox Phaser 6120N Printer

1 Answer

System not initializing


Does the machine have a network box on back? Frequently on that product the boards in the network controller come lose, and simply need reset.
You can unplug all accessories and see if it powers up then, then connect them back one by one and see which one causes the failure.

Feb 10, 2009 | Xerox WorkCentre M-24 Color Copier

2 Answers

Xerox WC Pro 35 - Error 14-563


this code means your scanner has failed to setup correctly. this could be a problem that you would need a qualified tech to service the copier. there is nothing that you can do after you power off and power on (popo) the copier. it could be voltage, pwb board, or a binding scanner assembly.

Sep 21, 2008 | Xerox WorkCentre M118 Black and White...

1 Answer

Xerox Phaser 8560 Will Not Power On


The 8560 has a one year warranty. Call 1-800-835-6100 and they will come out and fix it.

Aug 07, 2008 | Xerox Phaser 8560MFP Laser Printer

2 Answers

Xerox Phaser 8500DN - no power


1) verify that the power is plugged into a known good power plug in the wall. make sure there is not a surge protector, extension cord connected to it.

2) disconnect any usb and/or ethernet cables.

3) reseat the ram

4) disconnect any optional accessories such as lower trays, hard drives, etc. to isolate any possible items taking down the printer.

Jun 11, 2008 | Xerox Phaser 8500/DN Printer

Not finding what you are looking for?
Xerox WorkCentre PE16 All-In-One Laser Printer Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Printers & Copiers Experts

Whit
Whit

Level 1 Expert

185 Answers

iteminconline

Level 2 Expert

110 Answers

Philip Hughes

Level 2 Expert

63 Answers

Are you a Xerox Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...