Question about Boss IQ 3KD.1 Car Audio Amplifier

1 Answer

Need a power connector for a Boss IQ 3KD.1 amplifier

Where can I find a replacement power connector for a Boss IQ 3KD.1 3000W Class D Monoblock Amplifier. The screw loosened on the +12 terminal and it melted the terminal and the plastic.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 3,130 Answers
Re: Need a power connector for a Boss IQ 3KD.1 amplifier - Boss IQ 3KD.1 Car Audio Amplifier Car Amplifiers


Posted on Mar 31, 2006

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How do i wire 2 fosgate punch 10" subs to this boss iq 680.2 amp? the subs are rfd2210 hx4 and theres two subs in a separated seald box. i need to know how to phase all the vcs together

Your subs are 4 ohm dvc so lower the impedance more power from your amp. I will include a link that will show you how to wire your subs for maximum performance. I would explain it but seeing the drawing will make more sense....

Sep 23, 2010 | Boss IQ 680.2 Car Audio Amplifier

1 Answer

It wont come on

you or sumone while connecting the 12v power touched the screwdriver to the side of amp shorting the amp out sorry cant be fixed by anyone but who makes it or has internal board knowledge

Apr 15, 2009 | Boss IQ 3KD.1 Car Audio Amplifier

1 Answer

Will my car stereo power 300 watt speakers?

it will power them but it will only push a small amount of wattage to them. something like 45 watts so they won't be very loud but if you run the wires you will hear them. It's beneficial to just invest in an amp you can pick up a 200 watt pretty cheap these days. and you will be much happier with the end result.

Mar 07, 2009 | Boss IQ 3KD.1 Car Audio Amplifier

1 Answer

Trying to figure out what kind of amp i got amercian pro vs-3507?

The VS3507 Is a class D monoblock.
Your optimum wiring for this amplifier is a 2 Ohm load - so it produces its full potential power of 350W RMS.

To Achieve a 2 ohm load, the most common load is one of the following...
(1) Dual 4 Ohm Voicecoil Subwoofer Wired in Parallel.
(2) 4 Ohm Voicecoil Subwoofers wired in Parallel.
(1) Quad 2 Ohm Voicecoil Subwoofer wired in Parallel/Series.
(1) Single 2 Ohm voicecoil subwoofer.

American Pro VS3507 2000W Car Audio Monoblock Amplifier
American Pro VS3507 Monoblock Amplifier Details
  • Built-In Crossover
  • Variable High/Low Pass Filters
  • Phase Shift Control
  • Subsonic Filter
  • Bass Boost Control
  • Dancing Lights at the Rhythm of Music
  • Protection Circuits
  • Gold Plated Terminals
  • Power & Protection Circuit LED
  • 1 x 250 Watts RMS @ 4 Ohms
  • 1 x 350 Watts RMS @ 2 Ohms Thanks for using FixYa - A FixYa rating is appreciated!!

Jan 29, 2009 | American Pro Car Amplifiers

1 Answer

How do i hook up the speakers

connect each dual in series then parallel each sub

Sep 08, 2008 | Boss IQ 3KD.1 Car Audio Amplifier

1 Answer

How to hook up 2 10 inch speakers

For best results the output resistance of the amplifier must equal the combined resistance of the speakers. So if the amps says 8 ohms and you have two 4 ohm speakers you put them is series or if the amps says 4ohms and you have two 8 ohm speakers put them in series. If it says 4ohm and you have two 4 ohm speakers best to use only one. It Depends on the output resistance of the amps. It is usually written at the terminals where the speakers are connected.

Sep 08, 2008 | Boss IQ 3KD.1 Car Audio Amplifier

1 Answer

Is it good or not

HI qq_lando,

Yes, you can get good bass from this setup. The Boos amp can handle 1 ohm but no less. You should be fine if your using one, no more than 2 kickers. You will need to configure the wires different for 2. Direct connect + to + and - to -. I must suggest if you have Dual Voice coil to wire your Solo X in series to keep the Ohms up. Main thing to remember is keep it below 8 ohm and above 1 ohm total impedance

Nov 09, 2007 | Car Amplifiers

1 Answer

On power up.......protect light comes on

what are the resistors connected to? mosfets?if so you need to identify which pin gate or source,these amps have dual so the other side would be the same.

May 04, 2007 | Boss IQ 1080.2 Car Audio Amplifier

Not finding what you are looking for?
Boss IQ 3KD.1 Car Audio Amplifier Logo

Related Topics:

285 people viewed this question

Ask a Question

Usually answered in minutes!

Top Boss Car Amplifiers Experts

Tygh Duval
Tygh Duval

Level 2 Expert

290 Answers

Mike Neath
Mike Neath

Level 3 Expert

315 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Are you a Boss Car Amplifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides