Question about AT&T 944 Four Line Intercom Phone

1 Answer

It keeps on beeping

I unplugged the phone system and then plugged it back in but it will not stop beeping. How do i stop that?
ron

Posted by on

  • Anonymous Sep 29, 2008

    We had a power failure for a few hours.
    Now one of the three phones, is constantly ringing.
    The other 2 are not. I tried replacing the batteries.
    that didn't help. Any ideas?


×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

This happened to me today!
Do the following in order:

1.take battery out of back of phone
2. unplug all phone lines from phone, then unplug all phone lines from wall
3. unplug ac from phone, then from wall
Wait 30 seconds.
In this order:
1. replace battery
2. replace phone line(s) to phone, then to wall
3. replace ac to phone, then to wall.

These steps solved it for me! Good luck.

Posted on Feb 05, 2009

  • LeAnn Murphy
    LeAnn Murphy Oct 08, 2014

    Unfortunately for me, this hasn't stopped the beeping. Why doesn't AT&T have more info on this!?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2011 Nissan Altima .. High pitched beeping for 3 seconds when starting the car or turning the car off


Sounds like your alarm system. If you know how reset it or unplug it and plug it back in see if that helps or you can always just leave it unplugged. That should stop the beeping.

Jul 07, 2014 | Cars & Trucks

1 Answer

Refrigerator is not on, constantly beeping. will not turn back on no matter what it is plugged into; it just keeps beeping!


It might be calling for anti-freezing? Unplug the thing for an hour from the wall. I bet bleeping stops. Dont forget to plug it back in...

Aug 17, 2013 | Frigidaire Refrigerators

1 Answer

Why does battery beep and tells me its on battery power when it's stil plugged to wall. and i have a good power source


Usually that indicates a low battery charge or bad battery. Make sure you do not have the battery backup side overloaded with too many devices. Do not plug inductive loads with motors or heating elements into the backup. Turn the device off and unplug anything that is plugged into the bachup. Plug the battery backup into the wall with nothing attached and turn on. Wait 10-15 minutes. this will charge the battery. If beeping continues after this with nothing attached, you likely need a new battery or the control/monitoring system is bad. If beeps stop, reinstall and do not attach more wattage than the unit can suppluy

Jan 06, 2011 | APC BX800 Back-UPS XS 800 (APNBX800) UPS...

1 Answer

Whirlpool Microwave Hood Combination MH3184XPS-0 (October 2004), for no reason at all, this morning keeps beeping and running the power setting down from 10 to 1, and just keeps doing it in rapid sequence....


Ours just started doing this exact same thing this past Friday - 12/11/09. What's going on? The cook power just starts beeping all by itself and going from 10 down to 1 over and over again. It may stop momentarily, but then starts again within a minute or so - it's constant until we unplug it. We plug it back in and within a few minutes it starts doing it again. What gives?

Dec 08, 2009 | Whirlpool MH3184XP Microwave Oven

1 Answer

Unit keeps beeping even when unpluged. over load


UPSs will beep when unplugged to tell you that the mains is off! Overload should reset if you disconnect both the load and the power.

Jun 30, 2009 | APC Back-UPS CS 500 UPS System

2 Answers

My 480 NT Royal Cash Managment System shows "EE" on the screen and beeps not stop


turn the machine to PRG - unplug for 20 seconds. while pressing clr plug back in

May 25, 2009 | Royal Office Equipment & Supplies

1 Answer

My alarm keeps beeping and telling me that I have a ph failure. Can anyone tell me what this means. Thanks Ron


it means yu lost your phone communication. push the system status button after it says the tme problem it will beep. then press disarm o clear. if ou cant clear it you ned to have some 1 check if you still have a phone connction

Feb 25, 2009 | GE Security Simon 3 Wireless Home Security...

Not finding what you are looking for?
AT&T 944 Four Line Intercom Phone Logo

Related Topics:

680 people viewed this question

Ask a Question

Usually answered in minutes!

Top AT&T Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

george  peters
george peters

Level 3 Expert

860 Answers

Paul C.

Level 1 Expert

59 Answers

Are you an AT&T Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...