Question about RCA D52W19 52" Rear Projection Television

1 Answer

3 green blinks

My tv power light blinks three times between each blink is about 7 seconds. The tv wont power up. I have tried to change channels when its in the middle of a blink no luck, any suggestions.

  1. same problem, different model #

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • RCA Master
  • 5,138 Answers

Look on Deflection board cp 150 2200uf 16v capacitor and there is 2 more capacitors 220uf 35v replace both of them. Green and Gold writing on caps.

Posted on Sep 16, 2008

1 Suggested Answer

Slinteriors
  • 8617 Answers

SOURCE: 3 green blinks

thats the error code indicating that the flyback is bad. You need flyback 259296 and you can get a new replacement flyback at the following link and they provide free step by step instructions on how to do the repair which is very easy. Heres the link.
http://servicemanuals.vstore.ca/

Posted on Sep 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When i turn on my tv it tries to boot, blue mitsubishi home screen come up, i hear fan then it all shuts off while green light blinks.


Try a reset. Start by unplugging for 1 minute, then plug back in & if still won't restart try the following. If none of the following work, you will need a technician.

Initializing the TV in many cases can remedy a problem.
In the 2006 product line Initialization is now a user function.
Pressing the front panel "INPUT' and "FORMAT"
buttons at the same time activates Initialization. When
complete all user settings will have to be set again. The
table in Figure 4-3 list the User Initialization procedures.
Note: Pressing INPUT and FORMAT is the same as
the Initialization in the Option Menu (MENU-2-4-7-0)
Order Name Procedure Results Notes
1 System Reset Press <System Reset>
on Front Panel
Hardware & TV operating
software reset.
POWER/Timer LED flashes for 60
seconds. No customer settings
are changed.
2 User Initialization
Press <INPUT> &
<FORMAT> on Front
Panel at the same time.
All customer Audio &
Video settings are reset to
factory default.
All customer settings will need to
re-configured.
3 Reset System
Defaults
From the remote, press
<MENU> <1-2-3>
<ENTER>
All customer settings
except V-Chip are reset to
factory default.
Netcommand, Channel Memory,
etc., will need to be re-configured.
SERVICER
PROCEDURE 4 Initialization
From the remote, press
<MENU> <2-4-7-0>*
select "INITIAL" press
<ENTER>
All customer settings are
reset to factory default.
All customer settings will need to
re-configured.
MITSUBISHI RESET / INITIALIZATION CHART
CUSTOMER
PROCEDURES
Figure 4-3
Figure 4-4
LED Indications
The front panel LEDs, refer to Figure 4-4, also assist in
determining the cause of a symptom. Figure 4-5 illustrates
normal LED operation. Figure 4-6 shows the
LEDs response when a problem is detected and indicates
the possible cause.
Power/Timer
Indicator
Status
Indicator
Lamp
Indicator Condition
Off Off Off Off (standby)
Blinking green
fast Off Off Initialization (10 - 65 seconds)
Off Off Blinking
green fast Lamp runs for 1 min after PTV off
Green Off Off Power On
Blinking green Off Off Power On Timer is set
NORMAL LED INDICATIONS
Power LED Status LED Lamp LED Condition
High Temperature - check ventilation air flow.
(Temperature sensor is disconnected.)
Off Off Blinking yellow Lamp cover is open.
Lamp failure (Lamp fails to turn on)
Off Off Red (Lamp turns off after lighting)
Lamp is broken
Off Blinking Red Off Fan Stop
Off Red. Off Circuit failure. (Run Error Code Check)

Apr 08, 2015 | Mitsubishi WD-65731 65-Inch 1080p DLP HDTV

1 Answer

I have a Mitsubishi WD-62525 HDTV that suddenly wont turn on. Just has a green blinking light when you hit the power button. Any ideas?


I found this on another website, most likely it is your power supply capacitors.
  1. Press the "reset" button and hold for 10 seconds .... Does TV turn on and blinking green light turn to solid green.

  2. Unplug the TV from it's power source for various times, ranging between 5 minutes and 24 hours..... Does blinking green light continue upon plugging in the TV.

  3. Disconnect ALL devices from the TV; DVD, Tuner, Cable Box, unplug the TV for various duration times .... Does blinking green light continues upon plugging in the TV.

  4. Press Power and Menu buttons simultaneously and hold depressed for 20 seconds .... Does blinking green light continue to flash.

  5. Press Power and Display buttons simultaneously and hold depressed for 20 seconds .... Does blinking green light continue to flash.

  6. Insure that no front panel buttons are inadvertently stuck in an "engaged" position.

Diagnosis: If none of the above test resolve the issue, then the failure lies in one of the following:

  1. DM Module Capacitors have FAILED.
  2. DM Module is defective.
  3. EEPROM Board failure
  4. Power Supply failure.

Feb 28, 2011 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Hi, i have here a mitsubishi WD-57733. once the unit is switch ON, green LED light and a few seconds the status LED light then shuts off. I think light engines good since i just replaced a new lamp.


hello i've just checked the manual for here is some information

None TV is powered off. Normal operation.

Green TV is powered on. Normal operation.

Green 1. TV just plugged into AC outlet.

Wait until blinking stops before turning on (approximately 1

minute). Normal operation.

2. AC just restored after power failure.

3. TV Rebooting after System Reset was

used.

4. TV Rebooting after power fluctuation

or receiving abnormal digital signals

from digital channel, or digital device.

5. You have begun the procedure to

update software from an authorized

flash memory device.

For detailed information, see the instructions that accompany

the authorized software update. IMPORTANT: Do not

use unauthorized software at any time.

Green TV just powered off and lamp is

cooling.

Starts to blink 30 seconds after turning off TV. TV can be turned

on before blinking starts or after blinking stops, but not while the
indicator is blinking. Normal operation. hope it helps regards shaun
Green TV powered off and auto-on timer is set. Normal operation. TV can be turned on at any time.

Dec 06, 2010 | Mitsubishi Projection Televisions

3 Answers

IT TURN OFF ITSELF RIGHT AFTER TURN ON GREEN


Hi,
If the Lamp red light is blinking then replace lamp, replacement procedure is written in user manual and its easy.
If standby/ power red light is blinking then please count its blinking and post here. It is an error code that has info about problem in specific section of tv.
You will see 3 seconds long pause between blinks so count pause to pause.

May 11, 2010 | Sony Grand WEGA KDF-60XS955 60" Rear...

1 Answer

TV wont turn on, the power light turns green for a second then blinks three times and turns off?


That blinking light represents an error code,give Mitsubishi a call they will help you troubleshoot and diagnose your problem and if needed help you set up service. 1-800-332-2119 Good luck !

Nov 29, 2009 | Mitsubishi WS-55411 55" Rear Projection...

1 Answer

Timer light blinks on and off and tv wont turn on


Resetting the TV
If the buttons on the remote AND the buttons on the TV case do not work (channels do not change and you cannot open or navigate the menu), the TV has stopped responding. Reset the TV as follows:

NOTE:
Some TVs have a reset button. If available and accessible, try using the reset buttons before using the steps below. Using the reset buttons can save time.
1. Unplug the TV power cord from the power outlet.
2. Unplug any connected devices (DVD, Set-top boxes, etc...)
3. Press and hold the TV power button for five seconds.
4. Plug the TV power cord back into the power outlet and turn on the TV.
5. Open the on-screen menu to confirm that the TV is responding again.
6. Turn off the TV and reconnect the devices.
7. Turn on the TV.
If ever resetting is no effect then the problem is in the "DM board"
The constant blinking green light means that the TV is not booting up. This is a common problem on this set. Hope it may help you; Regards, VOTIT

Sep 25, 2008 | Mitsubishi WS-55809 55" Rear Projection...

1 Answer

3 green blinks


thats the error code indicating that the flyback is bad. You need flyback 259296 and you can get a new replacement flyback at the following link and they provide free step by step instructions on how to do the repair which is very easy. Heres the link.
http://servicemanuals.vstore.ca/

Sep 08, 2008 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

Panasonic PT-53TW53G


If the front power light is blinking three times then your TV has a problem with the convergence. You can get the correct replacement parts and full step by step photo instructions from www.TvRepairKits.com

Aug 17, 2008 | Panasonic PT-53TW53 53" Rear Projection...

1 Answer

Samsung HLM507W Blink Lights


beings the connectors were different on the new bulb the spark gap maybe different also if it is the lamp wont work in that unit

Apr 12, 2008 | Projection Televisions

Not finding what you are looking for?
RCA D52W19 52" Rear Projection Television Logo

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

Are you a RCA Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...