How do I make my wbr 1310 router secure - D-Link 802.11g Wireless Router WBR-1310 (WBR1310)

Go to http://www.dlink.com/products/?tab=3&pid=WBR-1310&rev=WBR-1310

and select the data you want. The software is down loadable. make sure that your router is not a B or C version as the one shown is just for the WBR-1310. It also has setup instructions if you want to learn to do it your self rather than default to setup software.

There are multiple versions of both of your routers, you can click on your version and try there tech info from there. If you have no luck, just post the right versions here and I'll see what I can do for you.

.............................................................................................................

There are multiple revisions of the WBR-1310, each with revision specific drivers, firmware, installation guides, and other resources.

• WBR-1310
• WBR-1310_REVB
• WBR-1310_REVD

There are multiple revisions of the WBR-2310, each with revision specific drivers, firmware, installation guides, and other resources.

Go to there support page and click on your model.

• WBR-2310
• WBR-2310_REVB

http://www.dlink.com/products/default.aspx?pid=WBR-2310&tab=3

You can follow these steps in enabling wireless security on your router and do this steps using a computer wired to the router since once you save the settings your wireless network will be secure.<br /><br />1) Open the internet browser and type the address 192.168.0.1 to login to the router. The default username is "admin" and leave the password box empty.<br />2) Click "Wireless Settings" on the left side.<br />3) Select the Security Mode ,Enable WEP Security.<br />4) Select the Authentication ,Shared Key.<br />5) Select the WEP Encryption , either 64-bit or 128-bit.<br />6) Select the Key Type ,HEX (only A-F and 0-9 number allowed) or ASCII (all number and character allowed).<br />7) Enter a WEP key as your security password to login to your wireless later.<br />8) Press Save Settings to save all settings changed. Reboot the router.<br /><br />

By going to the security setting in the router and assigning a WAP/WEP "Key" this will then enable security. Please consult your manual for how to do this.

ftp://ftp10.dlink.com/pdfs/products/WBR-1310/WBR-1310_ds.pdf
manual above

theres a couple of version of this router http://www.dlink.com/products/default.aspx?pid=WBR-1310&tab=3 I'm using the manual from here http://www.dlink.com/products/?tab=3&pid=WBR-1310&rev=WBR-1310
on a working PC download and install this program http://www.xirrus.com/library/wifitools.php this will detect all the wireless signals being broadcast - see if the router is actually broadcasting - if it is detected on your PC then it may be that 1) the firewall is blocking access or 2) the security code is entered wrong - -log into the router and remove the wireless security and see if you can now detect

To secure the wireless network, you will need to access the router set up.
Is there any computer connected to the router ?
If not then you will need to connect the router to the computer .
Then check the IP address of the computer and open the router set up.
Click Here for step by step solution on how to secure the network

Just open the router's setup page by going to http://192.168.0.1 you can see it under the Wireless Security tab.

Go the router setup page, 192.168.0.1, type admin as the user name and password as the password (default, if you have changed these use your login info).
Then on the wireless page change the SSID (router name).
You can also add a security key on this page.

http://support.dlink.com/emulators/wbr1310_revA/wireless.htm

more info from D-Link:

http://www.dlink.com/products/support.asp?pid=474&pv=96&sec=1

Click on this link or copy and paste the complete link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Try to uncheck UPnP Enable on your router located on advaced network setting. or try reconfiguring your wireless network settings.

Try creating a new wireless connection network or disable the UPnP on your WBR-1310.