Question about Xact Communication XG2200 Cordless Phone
Unplug the base and phone connection. Remove battery. After a minute plug in phone and connection and then put the battery back into phone slot.
It worked for me!
Posted on Jan 22, 2008
I solved this problem with a RESET of the handset. Instructions from the Philips website: Please perform a reset of your device. You will not loose your recorded data (phonebook and personal settings are being kept). 1. Unplug the mains of the base station. 2. Remove one of the batteries of each handset. 3. Put the batteries back in and re-plug the mains of the base station.
Posted on Aug 27, 2007
Here are the directions from Panasonic's Website. I just tried them and it worked perfectly. Re-registering the Handset If ?No link to base. Move closer to base, try again.? is displayed even when using the handset near the base unit, the handset may have lost communication with the base unit. You need to re-register the handset to the base unit. ? Make sure the base unit is not being used. ? Have both the handset and base unit nearby during registration. ? Follow steps 1 and 2 listed below. You have about 1 minute to complete them. 1 Base unit: Press and hold [HANDSET LOCATOR] until a beep sounds. ? The CHARGE indicator flashes. 2 Handset: Press and hold [FLASH/CALL WAIT] until ?Handset Registering? is displayed. ? When registration is complete, a beep sounds from the handset. ? Wait for 20 seconds after registration is complete while the handset establishes communication with the base unit. ? If the handset beeps 3 times and ?Error!!? is displayed, an error occurred. Try again from step 1. ? You can stop registration by pressing [OFF] on the handset, and pressing
Posted on Jun 06, 2009
Try to refit ics inn handset then keep for charging for 3 hours then it may work properly
Posted on Feb 27, 2007
The handset has this message on it when i press the talk button. no link to base,move closer to base, try again
Posted on Feb 07, 2007
The RF section in this unit is located in a removable module. Unfortunately, the connector on this module uses really cheap metals that oxidize (tarnish) after several years... this allows Uniden to make an extra $1 in profit on each phone, and guarantees the phone won't last very long (so you will buy a new one soon). If the handset still works the way it normally does when "out of range," this procedure MAY restore your phone to working condition: 0. Disassemble the base unit. 1. Unscrew & remove the RF module. 2. Remove the shiny plastic shell (fake shielding). 3. Gently clean the exposed contacts with a "dremel" type rotary wire brush at low speed. 4. Spray PLASTIC-SAFE electronic contact cleaner into the socket.* 5. Mate/un-mate the connector 5 to 10 times. 6. Rinse the socket with ammonia from a spray bottle (to provide some pressure). 7. Allow the ammonia to evaporate completely (do not apply heat). 8. Re-install the RF module. 9. Power on & test. Maybe it's good for a couple more years! *OBEY ALL HEALTH PROTECTION GUIDELINES FOR CONTACT CLEANER; A SINGLE EXPOSURE TO THESE CHEMICALS CAN HAVE MEASURABLE EFFECTS ON YOUR IMMUNE SYSTEM.
Posted on Jan 27, 2007
I unplugged the base unit from the wall plug and re-connected it. I was able to link with the base after this.
Posted on Jan 20, 2007
Try leaving it on the base for a while, overnight. It might resync. Do you have another similar cordless in the house? if you do and someone accidentally placed a phone on the wrong base, that would result in both of them loosing communication with the bases, untill you placed them back in their own bases. Good luck
Posted on Mar 14, 2006
Another solution is power off the base for a while (2 or 3 minutes), reconnect the power whit the han set on the base. this resync the phone
Posted on Mar 09, 2007
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Nov 10, 2013 | Exhaust Gaskets & Seals RemFlex Exhaust...
Oct 10, 2011 | Lexmark X2500 All-In-One Printer
Jul 21, 2010 | Uniden DECT 6.0 Cordless Phone ID
Feb 14, 2010 | 2007 Dodge Nitro R/T New Cars
Oct 27, 2009 | Philips Magnavox DVD/VCR Dual Player
Aug 31, 2009 | Lexmark C533DN InkJet Printer
Aug 30, 2009 | Lands Phones
Mar 12, 2009 | Uniden Cordless Phone
753 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: