Question about Zebra Z4Mplus Label Printer

2 Answers

How to reset flash

I down load firmware and it error out. How do I reset the flash. The printer just keeping download firware.

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert that has over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 214 Answers

Go to the printer software update then select configuration and then under check for updates select never and close the window

Posted on Sep 09, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Zebra Master
  • 19,396 Answers

Allow the printer to finish download, I will see if there is downloadable firmware online.

Posted on Sep 09, 2008

  • Ginko
    Ginko Sep 09, 2008

    If you interrupted the firmware download procedure, then you may have damaged the firmware eeprom.
    In this case the eeprom must be removed from board, installed on an eeprom programmer, and re flashed with the firmware image.
    Download firmware again, and try restarting firmware update procedure. If you cannot finalize the procedure find a good local repair shop with a good engineer that knows how to restore the firmware image in the printer.
    Try restarting the update here is download page.


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What does error 49.4C02 Service error on HP Printer 2420dn

it is a bad or print job the 1st time if it keeps popping the code then
you need to flash the firmware which is easy. use a usb hook it to a laptop undo the network so no can send a job to it set up laptop to
print to it, so go to load driver then print then on the same page from hp download firmware and the installer read the how to then flash it,let it run its cycle it will turn on and off 1 or 2 times then it will come up to ready. if it keeps popping the code then check your cat 5 cables make sure they r in good shape if so, then ur looking at a
bad formatter board, $200 up is the price. go to ebay or look for on google a company that buys and sell used ones un plug remove to
screws install formatter turn on and in the printer put your ip gateway
and sub and ur good to go. but 75% of the time its firmware

Jul 13, 2014 | HP LaserJet 4600dn Color Printer

1 Answer

Error code C-E002

IF THIS HAPPENED AFTER UPDATING FIRMWARE "The HDD Version Up procedure has not been completed"


Jul 10, 2013 | Konica Minolta bizhub C450P Laser Printer

2 Answers

We have a M2727 Laserjet Printer/Fax . We can print, and we can receive fax, but our problem is sending a FAX.. Keeps giving us an error code of 49. Please advise Thank-You, Marla

I found this on the HP website:

HP LaserJet M2727 Multifunction Printer Series - 49 Error Message Is Displayed While Faxing ISSUE: The printer control panel will be displaying 49 service error while sending faxes. The receiving fax will be lost, and the printer will display the same error even after reboot. SOLUTION: Performing a factory reset and a firmware upgrade is the only solution for this issue. Step 1: Performing a factory reset Restoring the factory-set defaults returns all of the settings to the factory defaults, and it also clears the fax header name and phone number. CAUTION: This procedure clears fax numbers and names that are associated with one-touch keys and speed-dial codes, and deletes any pages that are stored in the memory. The procedure then automatically restarts the product. Perform the following steps to restore the factory-set defaults: 1. On the product control panel, press Setup . 2. Use the arrow buttons to select Service , and then press OK . 3. Use the arrow buttons to select Restore defaults , and then press OK . The product automatically restarts. Step 2: Firmware upgrade After coming to ready, upgrade the printer firmware from the HP website. The issue can be fixed with any of the firmware upgrade available now. Firmware version 20080505 and higher versions have the fix. You can download firmware version 20080612 from the HP LaserJet M2727 Firmware Update 20080612 webpage. Click here to go to the HP LaserJet M2727 Firmware Update 20080612 webpage ( . The preceding steps will resolve the issue.

Mar 07, 2011 | HP Office Equipment & Supplies

2 Answers

I'm wondering how to repair a 49. 4C06 Service error

See if the error is only occuring with a particular application or certain documents. Most times the error is related to the use of Adobe. If you have a network and are using a print server for all the printers, then the first thing I would do is load one of the problem printers locally on one or more pc's using tcp/ip and the driver being loaded on the local machine. See if you still have the issue. If not, then the print server may be causing issues. If you still have the issue, especially with the 4250, then I would contact hp tech support. Keep in mind if it is only happening with a certain application, HP will tell you to contact that vendor. One other note is that I have seen this type of error of the 4200 and 4300 series when users were printing lots of documents with foreign language characters in them. On those, though the firmware upgrade solved the isse.

Feb 25, 2011 | HP Office Equipment & Supplies

1 Answer

Ibm 6400-008 with P62 error

P-62 error is DC program not valid. The printer cannot find the controller program or the validation checksum is corrupt.
You can try to reseat the flash (memory simms) but it probably will not help. You need to re-download the program (microcode) to the machine and if it still fails replace the flash with pre-writen flash.

If you need a copy of the microcode and instructions on how to load let me know here (I will try to keep an eye on this post)

Dec 30, 2009 | IBM Infoprint 1332 Laser Printer

3 Answers

My HP Laserjet 2420dn will not print and is displaying message '49.FF95 service error'. How can I fix this..?

This could be a firmware fault on the main formatter board inside the printer

1. Press CANCEL JOB to clear the
print job from the printer
2. Turn the printer off, and then
turn the printer on again.
3. Go to http:
support/lj2420, or
Click Download Drivers and
. Check for the
latest firmware image version
at the bottom of the page. If
this firmware image is newer
than the one installed on the
printer and the printer can
receive a firmware update,
download the newer firmware
upgrade. Not all printer
models can receive firmware update

Apr 26, 2009 | HP LaserJet 2420dn Printer

3 Answers

Zebra Lp 2844-Z printer flashing green and red alternately?

-Install ZDownloader from Zebra's web.- visit this page and do nothing to use in step 3 part to download for your stable firmware, only find and download it
-Turn off printer and get ready on Zdownloader sofware-You could see easly "Auto Detect Printers" on ZDownloader, press and hold the label feed button and keep your finger in there then click the "Auto Detect Printers", if you are seeing your printer in list now, continue to keep your finger in feed button-Select the firware.prg file, right click with select your printer in list and click "Download to Selected." -you are still keeping your finger in feed button in this time. You will see the feeding will start and your problem fixed.
Sorry for my english, haven't got enough practice.

Dec 30, 2008 | Zebra LP 2844 Thermal Printer

1 Answer

Printer erorr after down load of firmware

The printer probably failed in the final phase of download firmware.
After eight hours it is clear that the firmware setupwas not successfull.
This may have damaged the printer.
Keep the on button pressed for ten second, see if the printer turns off.
Try unplugging printer power cord, leave the printer unplugged for thirty minutes or so.
If the printer does not restart, the firmware inside the printer had been damaged.
In this case call the support number listed on your user manual.
If printer restart upgrade firmware again.

Sep 09, 2008 | Zebra Z4M Printer

2 Answers

Blk 0 chksum error

fault "blk 0 chksum error" is attributable to a corrupt firmware. Fortunately the firmware can be reloaded and restore the printer in operating condition. You can download a firmware from the site under support and drivers then download it in your PC. Normally you need to put the printer is flash download mode also instruction can be seen from the site. If you cannot do this I can assist you with this.

Jul 27, 2007 | Tally Line Matrix T6100 Printer

Not finding what you are looking for?
Zebra Z4Mplus Label Printer Logo

Related Topics:

359 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts


Level 2 Expert

254 Answers


Level 1 Expert

35 Answers

kenneth njonjo

Level 3 Expert

1575 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides