Question about Whirlpool Washing Machines

1 Answer

Goes through the wash. when gets to where suppose to remove the water for the rinse, it does not happen. Can put dile on rinse and well aget the water like in washing it, but still will not remove water or go to the spin.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 116 Answers

Most often than not your problem is a defective lid switch - easy test - use a pencil to poke the through the hole where the lid switch striker normally goes. open lid and poke it with selector on spin - need a new lid switch.

Regards

Posted on Sep 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my whirlpool model WTW57ESVW1 starts to rinse toward the end of the spin cycle?


The rinse is supposed to start during the spin...it's what removes most of the soap from your clothing! The spin forces the water through the clothes, flushing all but a small amount of the detergent away. The rinse cycle itself is more to remove solid debris that may have become trapped in the folds of cloth. It does so by floating and agitating the clothes.

The quick wash cycle is only for things that aren't soiled much, that you need to be done fast. It's not for everyday washing, just for things that maybe need no more than a freshening up. It makes it faster by cutting corners.

Sep 06, 2014 | Washing Machines

1 Answer

Maytag performa PAVT234AWW top load washer. The washer fills and spins fine. But when it is the wash cycle, the agitator makes a grinding noise and kind of vibrates in place. Is this something that can...


sounds to me like you have a bad transmission
what happens when you take the agetator off
does it still make the noise or does it go away?
if it goes away when you take the agetator off then you have a bad agetator

Aug 24, 2010 | Maytag Washing Machines

1 Answer

I put a new timer on. I tried to run a cycle. It


You need to replace the lid switch . Pt. # 8054980 . It is located behind the control panel , same area as the timet .

May 29, 2010 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

No cold rinse, only hot


Either the wires have come loose on the water valve or you have a defective water valve.Open the lid and look at the water valve. Are all wires connected?
If yes, replace the water valve.

Jun 24, 2009 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

I have a sears roebuck hd model 92279100 it will do everything but spin. We used to be able to lift up on the agitator and it would spin, but it won't do it now.


sounds like you have a bad drive block and basket drive you will have to remove the agetator to see the drive block. under the agetator there will be 2 small peices remove those. After that you will be able to see the drive block and basket drive ears. there are 2 slots that the basket drive fit into. if there are metal shavings and it does not look flush with something. this would be your problem. spin the drum and see what happens in that area. Have you ever heard a sound like thump thump thump? when it was spinning or slowing down? please let me know how it goes

Jun 04, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Water softener goes in at wash cycle rather than rinse cycle


if it has to go in the rinse,,this means you have to put it in the fabric softner compartment of the dispencer,,,also do not fill pass mark fill line in dispencer or it will sphion down by itself before time..onthejob

Jan 25, 2009 | Kenmore Elite 45986 Front Load Washer

3 Answers

Intuitive eco Iw811 Rinse 1 no water coming thru!


the 1st rinse light is normally set to "spray rinse", this means the machine will pump out the water, spin at medium speed then pulse cold water into the machine, this occurs for about 2 mins, then the machine will spin out, and advance for the final rinse which is a deep rinse.

Nov 15, 2007 | Fisher and Paykel Fisher Paykel Intuitive...

1 Answer

Hotpoint washer Won't rinse


your cold water valve will be your problem or you've turned the water supply off, if the supply is not off put the machine on to the final rinse if it fills it will be the main rinse valve gone. The cold water valve is a double one with 2 solaniods. Unplug the machine turn water supply off remove fill hose there are 2 screws keeping the top on, remove them lift the lid off.undo the screws that keep the valve on, take note wiring and remove pull the black hoses off, replace with new one. The resistance of the valve will be around 3.4 kohms

Oct 07, 2007 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...