I was given a tv with no remote. I have cable and a dvd player. I can not watch movies on my tv because I no remote. I have not been able to find a code so u can program my tv to my cable remote so I.can change the channel and be able to watch dvd's. Can u help me? My tv looks a lot Luke this one, its gray speakers on the side with a place to connect dvd cable chords to it and the serial number is F321CF0N2.

Assuming the DVD player has an HDMI port, run an HDMI cable from the DVD player to an available HDMI port on the TV. Let's say you have your TV service going to HDMI #1 on the TV, you can run the DVD to HDMI #2. When you want to watch a DVD, you must select the input/source on the TV remote to change it to HDMI 2(or whichever port you used). When ready to watch TV again, use the same button to change back to HDMI 1 (or whichever HDMI port you used for TV service). If you do not have an HDMI port on the DVD player, then you must use whatever type of connection it has and connect to the corresponding port(s) on your tv, Then follow same directions as above regarding choosing the input/source on the TV remote.

ok on dvd player u wann use hdmi cable direct to tv ok then select input hdmi on tv remote to see picture

The best option would be the HDMI-to-HDMI connection between your player and your TV. But because you mentioned that your TV is an old model, probably it does not have an HDMI port, in which case you have to use the RCA A/V connection. I understand you do not have a remote control for your TV, but you do not program a TV channel to watch DVD movies; you just switch between your TV and the DVD player as your audio/video sources. Here is what you have to do: check on your TV box for a button labeled 'Source' or 'Input'. Press on the button and it will alternate between TV and DVD (assuming you do not have any other device hooked up to your TV).

Hi,
You are trying to work out how to watch a DVD movie on your TV
The DVD should be connected to your TV with Audio Video cables.
And it will most likely be connected to AV1 on your TV
The easiest way to find out would be to

• Put a DVD in the Player and press play
• Now the TV is probably in channel mode, so find the button on the TV remote that says TV/AV
• now press this button TV/AV and it will scroll from TV channel to AV1, AV2 etc until you see the DVD picture.

I hope this helps you.
If so please leave a vote or comment.

Have a great day
MobileJB

Hi Russell,

TV's most commonly found in Hotels do not have an input button which is what you would use on almost every TV set out there.

I believe that if you go to channel 2 and then channel down there maybe an AV1, AV2, Video1, Video2 or even an A1, or A0, etc.. This is what you will need to tune the TV to in order to watch a movie from the VCR or DVD player using the RCA Cables.

Unfortunately there is not a user manual online at this time, but this is where you would find it:

http://www.p4c.philips.com/cgi-bin/dcbint/cpindex.pl?ctn=PCW127C199&slg=en&scy=US

Scott

All you should have to do is press the dvd button on your remote to go to the dvd player. Then press the vcr button to go back to the cable tv, if it is hooked up the same way as mine. And you can tell if it is by putting in a vhf tape and you can start watching it play. Otherwise you will need to press the input button on your tv remote until you see the vcr or dvd main screen. from there press the dvd button on your remote for the dvd player or the vcr button for your vhf. After you are done with watching your movies and wish to go back to the cable or tv programs use the tv remote and press input until the shows come back on

It sounds like you may not be on the correct input selection on the tv to watch the dvd player. Ther are probably three or four inputs to choose from on your tv. whichever input you hooked the dvd player into on the tv is the same imput you have select using the tv's remote control in order to watch movies on the dvd player.

ok cable sat wire goes into input of dvd-vcr input then coming out from the dvd vcr and into the moulator then a wire out to the tv now make sure your vcr is set to the right setting ...now you can record 1 cable..2.vcr dvd..3 modulator...4...tv make sure vcr is set to monitor

Jo have you plugged in the Audio and Video cable in correctly. You need to check that the Video cable is in the corresponding input on the TV

you should have a input select button on your remote. video 1 should be the front and video 2 should be the back. i had to buy 3 or 4 different universal remotes when mine messed up just to get the one button to change to change it to the inputs because there is no other way to change it to that with he buttons on the tv. kinda surprised that you didn't try and push that button yet.