Question about Whirlpool Washing Machines

1 Answer

Model #LA7000XM. broken belt, instructions on replacing

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Replaced the broken belt, instructions came with the belt.

Posted on Sep 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a broken belt 175D5131P003 on a GE washer Model WJRE5550K2WW, or a P620. I realize the belt will have to be stretched a great deal to fit over the drum pulley and the motor shaft, but cannot figure...


Hello & Welcome to FixYa

You can view this video for replacing the belt in your GE washer:


Please get back to me if you have any other questions.

Kevin

May 12, 2011 | Washing Machines

1 Answer

Ge washer making a noise trying to pump water out its a wslp1100doww model. How do u change the belt on the washer? precise instruction in detail would be great


if the belt is not broken you dont need to change it remove hoses from pump and clean the pump out...shopvac the water out of the machine first so you dont unleash it all over your house...

Apr 16, 2010 | GE Spacemaker WSLP1100D Top Load Washer

2 Answers

Will not spin


make and model number for accurate diag, but most common problem is broken wqasher tub drive belt, turn washer on its side and check for a broken belt.

Sep 27, 2009 | Washing Machines

1 Answer

Maytag dishwasher mdb50awq won't drain


HI. check the following areas for faults.

1. Air gap / Drain hoses
If there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: If there is no air gap installed, the dishwasher might not drain properly.

If the drain hose is clogged, the dishwasher would not drain. If there is an air gap installed, it is very common that a hose going from the air gap into the garbage disposer is clogged. Remove and clean the hose. Make sure to reattach the hose before starting the dishwasher.

Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.

2. Broken belt
Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.

Note: Sometimes the belt would just come off the pump. Even though it might not be broken, it is recommended that you replace the belt, because it is probably too stretched out.

3. Pump
Some models have two impellers inside the pump - one, wash impeller, takes care of the wash cycles, the other, drain impeller, drains the water out. If the drain impeller is broken (broken blades, shaft), the dishwasher would not drain. Replace any broken pump components.

4. Drain solenoid
Some models (for example most GE dishwashers) use a drain solenoid to drain water out. Sometimes the solenoid gets stuck, preventing the water from draining out. Try to free up the solenoid. If unsuccessful, you might have to replace the pump assembly.

5. Motor
If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.

Replace the motor if defective.

6. Timer
Replace if defective (note: uncommon problem).

Sep 05, 2009 | Maytag Washing Machines

1 Answer

Dishwasher not draining potential blockage with Bosch classixx


check the following areas to combat this issue.

1. Air gap / Drain hoses
If there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: If there is no air gap installed, the dishwasher might not drain properly.

If the drain hose is clogged, the dishwasher would not drain. If there is an air gap installed, it is very common that a hose going from the air gap into the garbage disposer is clogged. Remove and clean the hose. Make sure to reattach the hose before starting the dishwasher.

Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.

2. Broken belt
Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.

Note: Sometimes the belt would just come off the pump. Even though it might not be broken, it is recommended that you replace the belt, because it is probably too stretched out.

3. Pump
Some models have two impellers inside the pump - one, wash impeller, takes care of the wash cycles, the other, drain impeller, drains the water out. If the drain impeller is broken (broken blades, shaft), the dishwasher would not drain. Replace any broken pump components.

4. Drain solenoid
Some models (for example most GE dishwashers) use a drain solenoid to drain water out. Sometimes the solenoid gets stuck, preventing the water from draining out. Try to free up the solenoid. If unsuccessful, you might have to replace the pump assembly.

5. Motor
If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.

Replace the motor if defective.

6. Timer/control
Replace if defective (note: uncommon problem).

Jun 18, 2009 | Bosch Classixx WFL 2066 Front Load Washer

1 Answer

Replace Broken Belt


Here is the link that will explain how to do it:
http://www.applianceaid.com/amana-wash.html#belt
check this link u ll get if u dint really sorry for in convinience

Jun 17, 2009 | Amana NAV8805EWW 3.3 Cu. Ft. Elustra Tub...

1 Answer

Whirlpool washer won't spin in any cycle. Hose not clogged


Improper model number so I can't give repair instructions - but you can look for a broken coupling, drive belt - or lid switch.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Apr 02, 2009 | Washing Machines

1 Answer

Help with belt replacement


You have to remove the motor from the tub, there are 4 scews holding it on. then take off the pump using a star type bit

Dec 17, 2007 | Washing Machines

1 Answer

Tricty bindix


Sounds like you have a broken drive belt - if a washing machine doesn't spin, the usual cause is that the belt that goes between the motor and the wash tub has worn out and broken.

The usual procedure is to open the top of the unit and locate and remove the broken belt and replace with a brand new belt, the most expensive part of this repair is the labor, and it is not that difficult for most models if you have some basic tools.

Will need your specific make and model of unit in order to look up the part number of the belt and find out how easy the replacement process is, if you can leave this information, perhaps I can help more. :)

Good luck!

Nov 16, 2007 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...