Question about Jensen A300HLX Car Audio Amplifier

1 Answer

Connection how do i connect this model amp to a pioneer deck?

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Contributor
  • 64 Answers
Re: connection

Schematic & instructions on deck red (+) - power - 2 amp's power inlet power (+) black (-) - ground - 2 amp's power inlet ground (-) deck yellow wire - remote - 2 the remote amp deck outputs 2 the RCA amp inputs amp RCA outputs 2 speakers it is wise that a pro will install the system it will give u less concerns and u will have warranty on the installation this will save u the money u will spend for fixing a bad installation

Posted on Feb 06, 2006

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I have a pioneer 760watt model gm5100t amp and two audiobahn 12" subs and I would like to know how the wiring is configured from the amp to the subs as well as how the subs are wired since they are dual...

you bridge the inside + - and use the outside + -

then connect the outside + to the amp then connect the - to the + on the other sub then the - on the other sub to the amp just read this and do it slowly and you will get it then you only have to run the subs on a two channel amp

rate pls

Aug 14, 2010 | Pioneer GM-5300T Car Audio Amplifier

2 Answers

Noise through car speakers when connected to amp

If the subs are making a humming or RPM sound check your ground on the amp , make sure its a good ground. Always run your power wire from battery by itself down one side of vehicle. Groun should be no longer than 2 feet. If that dont help you can buy a noise supresor that goes inbetween your head unit and amp through RCA's with a ground on it . Hope this helps.

Jul 25, 2009 | Alpine MRD-M1000 Car Audio Amplifier

2 Answers

Mtx thunder 1501d

yes you can not run amps with your speakers being grounded un ground and then try

Nov 26, 2008 | MTX Thunder 1501D Car Audio Amplifier

1 Answer

Amp works but no sound from sub

Some older Pioneer radios require you to connect the Subwoofer RCA to the rear output on the back of the radio and then you have to turn on the subwoofer in the menu on the radio. What model Pioneer radio is it? Also, make sure that the RCA plugged into the amp is on the input side, not the output side.

Jul 29, 2008 | Sony XM-2002GTR Car Audio Amplifier

1 Answer

Hooking the mra-f350 to my highs

You will only need to connect the door speakers to the MRA-F350. In short, the connections will be as follows:

Deck---->MRA-F350 amp---->Door speakers
...................................\---->Sub amp---->Sub(s)

Just make sure you use the optical digital output of the deck to connect to the optical digital input of the MRA-F350 amp, not the RCA preamp connections.

Mar 13, 2008 | Alpine MRA-F350 Car Audio Amplifier

1 Answer

Not working

Make sure the remote (rem) port is powered, if not take another look at your inputs from the head unit as sometimes we tend to forget the channels orientation of ground and positive left and right.

If all else fails, have an audio installation expert help you out, a pari of extra hands would be helpful too...

Dec 09, 2007 | Pioneer GM-X372 Car Audio Amplifier

1 Answer

Amp trouble

Check the remote turn on line from your deck & make sure there is 12 volts on it when everything is on. Check the ground, too.

Jun 30, 2007 | Pioneer GM-D510M Car Audio Amplifier

2 Answers

Amp shuts off when music turned up

try adding a capacitor to feed the amp. these are large in capacity (farads)and dims (about 6' x3' dia.)...what wire size are you using?

May 30, 2007 | Sony XM-2002GTR Car Audio Amplifier

1 Answer

Amp is on, Subwoofer works, but no sound.

here is a short test you can try, remove the rca audio cable from the amp & connect a diskman or toher audio o/p device that you can hook up with the same rca wires, turn on the amp & see if you have sound. you can also remove the speaker wires from the sub & using multi meter read the ohm's of the sub, most subs are 4 ohm. Hope this help locate your problem

Oct 24, 2006 | Pioneer GM-7200M Car Audio Amplifier

Not finding what you are looking for?
Jensen A300HLX Car Audio Amplifier Logo

Related Topics:

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jensen Car Amplifiers Experts

Andrew Taylor
Andrew Taylor

Level 3 Expert

9503 Answers

Trippy Tripp

Level 2 Expert

191 Answers


Level 3 Expert

4507 Answers

Are you a Jensen Car Amplifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides