Question about Toshiba 43H70 43" Rear Projection Television
While TV was on, working fine, it just shut off. Power indicator light is blinking - hit the power button on the remote, power indicator light then blinks faster, but tv does not turn on. Hit the power button again on the remote, power indicator light is on steady, tv does not turn on. ???
You could have gotten an electrical surge that put your set into a shutdown condition and unplugging the set and letting the Microprocessor reset will fix this problem if it dosent blow out the main power regulator as you still or might I say have a regulator IC problem. IF THIS PROBLEM HAPPENS AGAIN MORE THEN A FEW TIMES WITHIN A SMALL TIME FRAME I WOULD HAVE THE SET LOOKED AT BEFORE THE REGULAOR BLOWS SOMETHING OUT!!!!
Posted on May 14, 2006
I am also facing the problem like this, TV power indicator blinks continously. TV doesnt come to normal
Posted on Feb 05, 2008
Try checking the projection bulb.Should be an axess panel on side of tv. Be sure the tv is cooled down and unpluged from the wall.Bulb held in with 2 screws. don't touch the lens of bulb.You will be able to see if bulb is good.
Posted on Feb 07, 2007
We had this problem on our tv. It would drive us nuts. If you unplug the TV from the wall, it would reset and be fine. Strangely enough, we moved and since it has been in the new house, roughly 3 months, the problem has never happened again.
Posted on Feb 04, 2007
I HAD A CONFERGENCE ERROR AFTER SEEING THAT I NEEDED TO AUTO TUNE. NOW THE POWER BUTTON JUST BLINKS. I TURNED ALL POWER OFF TO TV ALL NIGHT, THEN TURNED ON POWER. JUST A BLINKING LIGHT NOW . ANY HELP PLEASE. KEVIN MODEL 42H81 TOSHIBA
Posted on Feb 04, 2007
Remote is working correctly - tv was unpluggled and then plugged back in - everything working correctly...
Posted on Jan 12, 2006
My TW40F80 (10 yrs.old) kept going out and power light blinking. When turning the power off then on did not bring it back any more, I had service. The tech 'rebuilt the convergence circuit' with a $70 part from his truck. Works fine now, but total cost was $99 service call, $75 part and tax and a whopping $229 labor for about 45 min. of working on the convergence circuit. TV works great $404 later.
Posted on Jan 11, 2008
1. make sure the power card is plugged in, then press POWER. 2. the remote control batteries my be dead. good luck :-)
Posted on Jan 11, 2006
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Feb 04, 2013 | Sylvania Televison & Video
Apr 01, 2012 | Toshiba 36AF43 36" TV
Oct 11, 2011 | Panasonic PT-47WX49 47" Rear Projection...
May 29, 2011 | Sony FD Trinitron WEGA KV-13FS100 13" TV
Standby/Power light of the TV blinks when there is any internal malfunction in
the TV. The self-diagnostic function of the TV will cause the STANDBY light to
blink or flash when the television detects an issue. The number of times the
STANDBY light flashes corresponds to a specific issue.
examples are given below; some of the issues may be resolved without the need
1 blink / 2 blinks / 5 blinks: - This indicates that there may be a power-related problem with your set.
3 blinks: - This indicates that there may be a power-related problem with your set. The set will need to be serviced to allow a technician to determine the specific issue that needs to be repaired. If the power light flashes three times in sequence in a Lamp TV, the lamp cover is not securely attached. Reattach the lamp cover to resolve this issue.
4 blinks: - This indicates that there may be a back light or lamp power problem.
6 blinks: - This indicates that there is some kind of audio problem with your set.
7 blinks: - This indicates that there is a temperature problem with your set. Please check to make sure that the air vents on the sides and back of the set are not blocked or clogged and there is adequate ventilation around the television. We recommend that you check and clean the vents periodically to make sure the set receives adequate air flow. If the problem continues, the set will need to be serviced.
8 blinks: - This indicates that there may be a video-related problem with your set. If the flash sequence is not listed above or the light continues to flash, follow the steps below to perform a power reset:
Try the following steps to check if the issue can be resolved.
Turn off the television.
Unplug the television power cord from the electrical outlet.
Let the television remain without power for 60 seconds.
Plug the power cord back into the electrical outlet.
the television is plugged into a power strip or surge protector, remove it from
the power strip or surge protector and plug it directly into the wall outlet.
If the issue is resolved, the problem is with the power strip or surge
protector and not the television.
the issue continues to occur, service may be required.
for using Fixya.
Mar 02, 2011 | Sony KDF-E42A10 42 in. LCD Television
Feb 14, 2010 | Sony FD Trinitron WEGA KV-36HS510 36" TV
Jul 08, 2008 | Sony FD Trinitron WEGA KV-27FS120 27" TV
Nov 11, 2007 | RCA D61W20 61" Rear Projection Television
Aug 06, 2007 | Sony KV-32FS13 TV
Oct 13, 2012 | Toshiba 43H70 43" Rear Projection...
Jul 03, 2012 | Toshiba 43H70 43" Rear Projection...
1,444 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: