Question about Technics SL-DZ1200 CD Player

2 Answers

My player drags in turntable mode

My player is dragging in turntable mode...in CD and sd player mode..please help!!!!!

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,952 Answers

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,665 Answers

It must be reseted. Try unplug power for ten minutes and replug. If no result check if you can remove its internal small battery and refit.

Posted on Sep 20, 2008

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The turntable started dragging and now the record won't finish because it stops. What's wrong ? do I need a new turntable motor? Everything else seem to be working fine thxs David


Is this a cd player or a turntable recordplayer ???

cd player that drags usually mean theres a misalignment in the tray that holds cd

turntables that drag unless they are direct drive usually need there rubber drive tires replaced or a belt what ever it has

Oct 23, 2015 | CD Players

1 Answer

I have a technics CD player with volume problems


Any cd player will only have one level output, i think you may have it plugged into the "phono" connection on your amp, which is different for turntables, please recheck.

Feb 28, 2015 | Technics CD Players

1 Answer

Wurtlizer k99 turntable spins continously (with the cds) and wont go into test or play mode


Hello,

If the "turntable" you're referring to is the carrier where the CDs are stored, most likely your light gate lamp is burned out. Look underneath the carrier full of CDs at the front and you should see a faint glow. If you don't, and the K & Z LEDs on the Selection and Credit Computer are constantly lit, you'll need to replace the light gate bulb. I have these bulbs and can help further over the phone. Please don't dis-assemble anything without talking to me, or you may get the light gate assembly out of adjustment. Please email tech@wurlitzer-ohio.com.

Jan 28, 2010 | Wurlitzer Jukebox 1015 One More Time...

1 Answer

Turntable mode does not work


CHECK SENSOR & SENSOR SHEET UNIT DISPLAY UNIT
MAKE SURE NO LIQUID WAS DROPPED INTO UNIT

Mar 18, 2009 | Technics SL-DZ1200 CD Player

1 Answer

Numark cdx


have you checked the brake and start up settings they are the dials by the start and stop buttons it it is turned too far the platter will start up slow, you just trun to dial till you get the right start up speed you want

Jul 25, 2008 | Nu Mark Numark Cdx Table Top CD Player CD...

5 Answers

Technic sl-dz1200


I had the same problem. Replacing the sensor is not gonna help. it is a focus problem. I had to fold a small piece of paper and put it under the sensor to raise it up alittle then you screw it in. The size of the paper you will have to figure out for yourself, but it will help u fix your problem

May 18, 2008 | Technics SL-DZ1200 CD Player

1 Answer

In turntable mode the cd's are dragging their tempo


Found a video on a web site "how to remove the platter". It's a job which does'nt need a lot of skill just great care and patience. Within the video the guy will show the senors inside the platter itself. This is wear I found a huge build up dust which I blew off with a can of air. It's not a proffensional video but I found it very easy to follow. Unfortunate for though upon putting the deck back together again I've caused more damage with my clumsy haevy handed inpatience! After looking inside the deck (as long as you have no warranty left) you will see it is not that difficult and as a tip you can disconnect the lines of flat wires as they plug into the circuit board and are not soldered in. No soldering required to fix this. The guy who made this video deserves a lot of credit due to the fact he can save many of these decks from going to the bin! If I was rich and famous I would award him an Enviromental Gong.

Oct 23, 2007 | Technics SL-DZ1200 CD Player

2 Answers

My turntable is skippin wit some drag to it!!


adjust the fucos variable of the lens use little screw look under the lens.

Sep 12, 2007 | Technics SL-DZ1200 CD Player

Not finding what you are looking for?
Technics SL-DZ1200 CD Player Logo

Related Topics:

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Technics CD Players Experts

Josh Whitehead
Josh Whitehead

Level 3 Expert

1146 Answers

The Knight
The Knight

Level 3 Expert

68352 Answers

yadayada
yadayada

Level 3 Expert

61203 Answers

Are you a Technics CD Player Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...