Question about GE Profile JTP18 Electric Single Oven

4 Answers

DOOR Locked Flashing

After a 4 hour cleaning the DOOR LOCKED keeps flashing and the locking motor keeps running - constantly cycling locking and unlocking the door - but the DOORLOCKED Flashing does not change.

Posted by on

  • 4 more comments 
  • dennis1225 Sep 06, 2008

    is this the same swtich that controls the light? This seems fine.

  • dennis1225 Sep 07, 2008

    Where is the interlock switch - is it the same as the light switch on the frame that is closed by the door when shut?

  • dennis1225 Sep 07, 2008

    Fuses? Do I need to take the control panel off to get to fuses?

  • dennis1225 Sep 07, 2008

    micromaster - could a blown fuse cause the locking motor to cycle continuously? Seems like it would more likely be a sensor that looks for the door to be in the latched position.

  • dennis1225 Sep 07, 2008

    The link you provided does not provide any information on my problem.

    Where are the fuses?


  • dennis1225 Sep 14, 2008

    DO I need to take the control panel off to check for a malfunction latch? If the light goes off when the door switch is depressed does that mean that the door switch is working properly or are there multiple functions of the door switch and I need to remove it to see if it is failing even if the light is turning off?

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Where are the fuses located in the oven? I do not have a self cleaning oven and it keeps saying locked door and kicks off and will not cook again till it cools off. This happens everytime I use the oven.

Posted on Nov 21, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,952 Answers

Operating Check that door switch is completely closed. Check latch, solenoid, and actuation switch for electrical or mechanical malfunction.
Check wiring and test operation of door lock switch

Posted on Sep 14, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,614 Answers

Check the interlock switch, can be some object has stuck to it...

Posted on Sep 06, 2008

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 958 Answers

Hello dennis, this is what i found in the manual;

“LOCK DOOR” flashes The self-clean cycle has
in the display been selected but the
door is not closed.•

solution: close the oven door

LOCKED DOOR light is on when you want to cook.

The oven door is locked because the temperature inside the oven has not dropped below the locking temperature.

solution:• Press the CLEAR/OFF pad. Allow the oven to cool.


tnx 4 using fixya,

drcool

Posted on Sep 14, 2008

  • francis rivero Sep 14, 2008

    sorry, wrong arrangement oft he words for the first guide

    here is the correct one.

    LOCK DOOR flashes in the display

    the self clean cycle has been selected but the door is not closed

    solution: close the oven door.

    tnx again..
    drcool


×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you keep the door locked so you can use t self cleaning feature


Good Morning Friend,

I understand you want to know how to keep the door locked on your Frigidaire oven, model# FEB24S2AS, so you can use the self-clean feature. The "Door Locked" light will flash until the door locks when the self-clean cycle is in use. It glows constantly after the door locks. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.

-Best Regards-
WP

Jun 28, 2014 | Frigidaire FEB24S2AS / FEB24S2AB Electric...

1 Answer

How does the self-clean feature work on a Frigidaire CFEF366EMB model?


Hi Beverly,

I understand that you are looking to run your self-clean feature on your Frigidaire range, model# CFEF366EMB.

-To start this you will remove all racks and make sure that any excessive spillovers are cleaned up as best as you can.
-Next you will press the "Clean" button, and the display will show "---".
-Press the up or down arrows to select the length of time you want the oven to clean. Usually 2 or 3 hours.
-The door will automatically lock once your time has been chosen and the "LOCK" indicator light will flash. DO NOT open the door while the light is flashing. (it takes about 15 seconds for the oven door to lock).
-"Cln" will appear in the display during the self-clean cycle and the "LOCK" light will continue to glow until the self-cleaning cycle is complete or cancelled and the oven has cooled.

When the self-clean cycle has completed:
-The time of day or "END" will appear in the display window and the "Clean" and "LOCK" light will continue to glow.
-Once the oven has cooled down for about 1 HOUR and the "LOCK" light has gone out, the oven door can be opened.
-If "END" is in the display and the Clean indicator light remains ON, press the "CLEAR/OFF" button and the time of day will appear on the display.
-When the oven is cool, wipe away any residue or powdered ash with a damp cloth or paper towel.

-Best Regards-

Jan 23, 2014 | Frigidaire Ovens

1 Answer

How do i operate the self cleaning function


Hello - Before using the self-cleaning cycle of the appliance, remove the broiler pan and any utensils stored in the appliance. Also remove any excess spillovers in the oven cavity. Allow the oven to cool before cleaning. During the self-cleaning cycle, the outside of the wall oven can become very hot to the touch.

Typically to set the controls for a self-clean the first step is to confirm that the clock shows the correct time of the day. Press CLEAN. "---" appears in the display. Press the UP ARROW or DOWN ARROW once. "3:00" appears in the display for a 3 hour cycle. To change to a 2 hour cycle press DOWN ARROW"2:00" appears in the display. As soon as the controls are set, the motor drive lock will begin to close automatically and the "LOCK" indicator light will flash. DO NOT open the oven door while the light is flashing (it takes about 15 seconds for the over door to lock). "CLn" will appear in the display during the Self-Clean cycle and the "LOCK" light will glow until the Self-Cleaning cycle is complete or cancelled and the oven temperature has cooled.

When the Self-Clean cycle has completed, the time of the day or "End" will appear in the display window and the "Clean" and "LOCK" light will continue to glow. Once the over has cooled down for about 1 HOUR and the "LOCK" light has gone out, the oven door can be opened. If "End" is the display and the Clean indicator light remains ON, press CLEAR/OFF. The time of the day will appear in the display.

If it becomes necessary to stop or interrupt a Self-Cleaning cycle, press CLEAR/OFF. Once the oven has cooled down for about 1 HOUR and the "LOCK" light has gone out, the oven door can be opened. Restart the Self-Clean cycle once all conditions have been corrected.

Oct 19, 2012 | Frigidaire GLEB27S7A Electric Single Oven

1 Answer

Locked after self clean cycle


you may have a bad door lock . in this case replace. but first reinstall the door and run a new clean cycle and see if it unlocks .. mm

Jul 14, 2010 | GE JKP45 Electric Double Oven

1 Answer

My GE drop electric range will not turn on the self cleaning unit. I set the time and push start and it flashes clean oven, door lock, however, the door will not lock. I hear a clicking sounds, it beeps...


You will need to press the stop/cancel button, next press the self clean button, you do not have to set the time the cleaning cycle takes approx 3-1/2 to 4 hours and the cool down takes another 45 minutes to one hour, it will clean and cool down and you do not need to interrupt this cycle, it will let you know when it is complete.

Nov 14, 2009 | GE Profile JTP18 Electric Single Oven

1 Answer

F90 code flashing and i cant reset it


F90 Maximum oven door unlock time exceeded.
F91 Maximum oven door unlock attempts exceeded.
F92 Maximum oven door open time exceeded.
F93 Maximum oven door lock time exceeded.
F94 Maximum oven door lock attempts exceeded.


1. (F90, 91, 92, 93 & 94) Check the wiring between EOC & Lock Motor Micro Switch.

2. (F90, 91, 92, 93 & 94) Replace the Motor Door Latch assembly if necessary.

3. (F90, 91, 92, 93 & 94) Check for binding of the Latch Cam, Lock Motor Rod & Lock Motor Cam.

4. (F90, 91, 92, 93 & 94) Check to see if Lock Motor Coil is open. If open, replace Lock Motor Assembly.

5. (F90, 91, 92, 93 & 94) Lock Motor continuously runs - if Micro Switch is open, replace Lock Motor Assembly.

6. (F92, 93 & 94) Check oven door Light Switch - if open, replace Switch.

7. If all situations above do not solve problem, replace EOC.


F90 is a door lock code, Try this...
unplug the range.
wait 1 minute.
turn the range back on,
then while holding in on the oven door.
start another self clean.
wait 2 minutes.
then cancel the self clean.

do not release the door until the door lock light goes out.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question@#$%

Jul 07, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

Door locked after shutting down cleaning cycle earlier than


The oven door lock needs approximately 1 hour to cool down before the oven door can be opened after a self cleaning cycle has finished. If the lock does not open after the oven has cooled down, you can try....1) Unplugging the range or shut off the circuit breaker for 5 minutes. Plug the range back in or turn on the circuit breaker. Set the clock and try moving the door lock lever or opening the door. 2) Set the self-clean cycle again and only allow it to work for 15 minutes. Cancel the self-clean cycle and allow the oven to cool. Gently try moving the door lock lever or opening the door.

Most ranges today use 3 different types of door locks...one is a solenoid controlled lock ( you hear a loud buzz noise when setting or unlocking the lock and has a arm that you must move to set the lock )...another is a heat sensitive lock ( has a arm that you must move to lock and un-lock, makes no noises and has a spring that slowly moves to lock the door will the oven is heating up )...Some locks are motorized ( no handle to move, the motor locks the door by it's self when you set the range for self clean )... If the motorized and heat sensitive locks fails to open after the self clean cycle, you must access the lock and move it yourself to open the door. On the free standing ranges, most times you must lift the cook top to access the lock mechanism. On built in ovens, the oven must be pulled out to remove the top access panel to get at the lock mechanism. Some build in ovens can have the control console removed to access the lock system. On the heat sensitive style of lock, there are no electrical parts to operate the lock, usually you will need to replace the lock. On the motorized style of lock, you will have to use a ohm/volt meter to test why the motor will not work. On the solenoid style of lock, the solenoid is often mounted on the back of the range and can be accessed by removing the rear panel, some may be mounted at the front, such as in a built in oven. The failure of the solenoid style of lock is normally caused by a bad lock solenoid. In order to get your door open, you must operate the door latch mechanism manually. Unplug or remove power from the range. Take the rear cover off the range. Locate the door latch assembly and operate it manually and open your door. Then check continuity of the solenoid. Some of the latch assemblies have micro switches to supply power also. You may need to check them. You should be able to get the door open and use your range until you can get a tech to repair if you can not repair yourself.

If you've interrupted the clean cycle or have accidentally set the clean cycle with the oven door open, the latch may have engaged and now the door can't be closed because it will hit the latch. There may be a door activated* switch on the front face of the oven. In this case you may need to manually press that door switch with your finger while at the same time canceling the clean cycle to get the latch to retract so the door can close fully again.

May 17, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

Stove door locked and continues to beep and flash code F9


The F9 code indicates there is a problem with the door lock.

Try disconnecting the power to the range for 10 seconds and reconnecting. Open the oven door and hold the door switch plunger in while you try these things. Put the control into clean for 5 minutes then cancel clean. You must hold the door switch plunger in for the 5 minutes.

Try canceling the clean cycle without putting the control into clean.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question$$%^^%$

Mar 27, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

Door lock lites keeps flashing but the door is not locked


The F9 code indicates there is a problem with the door lock.

Try disconnecting the power to the range for 10 seconds and reconnecting. Open the oven door and hold the door switch plunger in while you try these things. Put the control into clean for 5 minutes then cancel clean. You must hold the door switch plunger in for the 5 minutes.

Try canceling the clean cycle without putting the control into clean.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question^%$@#$%

Mar 02, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

Door Keeps Locking and Unlocking after Power Outage


Located the switch - resetting fixed my stove as well.

Dec 17, 2007 | GE Profile JTP18 Electric Single Oven

Not finding what you are looking for?
GE Profile JTP18 Electric Single Oven Logo

1,274 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Ovens Experts

William Miller
William Miller

Level 3 Expert

8820 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a GE Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...