Smarthru icon blinks in taskpanel

blinking green red light Electric Kettles Questions & Answers ...

www.fixya.com > Forum > Tags > blinking green red light

Electric Kettles blinking green red light questions and answers. Ask your blinking ...the kettle lights up but won't heat up, just bought it, the on switch shows red, but it isnot working...what to do? ... Chef's Choice 677 Cordless Electric Kettle.

red icon blinking Electric Kettles Questions & Answers - Fixya

www.fixya.com > Forum > Tags > red icon blinking

Electric Kettles red icon blinking questions and answers. Ask your red icon ... Light will not stop flashing Even after descaling and cleaning thoroughly the red lightflashes. Any ideas? ... "On" switch blinks, kettle won't heat Our 4-week old kettle juststopped working. When we ... Chef's Choice 677 Cordless Electric Kettle.

A blinking red light can be a sign of the radio picking up radio frequency waves (RF) on your same frequency or a nearby frequency. There may something transmitting in your area which is causing the blinking light, or you may have another radio which could be stuck in transmit. One way to check this is to take the radio to a different location and see if the blinking still occurs.

Next, the question would be, does the radio function otherwise correctly? If so, continue to use the radio and do not concern yourself with the light. If the radio does not function properly, they you should send it to a qualified radio repair center for service.

Best regards.

Its the Anti-theft light that is blinking. Its called the Engine immobilizer system. See link the area of the Lexus brochure describing this feature. http://drivers.lexus.com/t3Portal/document/om/OM48C02U/pdf/sec_01-07.pdf

Dehumidifier? Sounds like a warning of some sort. A humidifier does a simple job, removing moisture from the air. If yours is not set up to drain, it could have a full holding tank. Empty it out and give it a rinse and it should be good. Drop a couple drops of chlorine bleach in it to keep down the mold growth.

If it isn't a full tank, it could be an air filter that needs cleaning or replacing. Often these things are programmed in and needs to be cleared. Clean and or replace any and all air filters and look for a reset button.

Good luck.

How many times does the red light come on ? It should blink a number of times, then go off for a little while, and start blinking again. The number of blinks within each cycle will help you find out what is wrong:
Number of 1-second red LED blinks followed by 2-second pause, then repeats:
2-processor thermal protection activated
3-processor not installed
4-power supply failure
5-memory error
6-video error
7-PCA failure (ROM detected failure prior to video)
8-invalid ROM, bootblock recover mode
(http://h18000.www1.hp.com/products/quickspecs/productbulletin.html#spectype=worldwide&type=html&docid=11632)

Here is a link to your printers manual. It has troubleshooting in it and explains what the error means when you see the picture of the sun with the ink drop & exclamation point blinking. It also has instructions on how to fix the error and stop the blinking.

http://support.dell.com/support/edocs/systems/1710n/en/om/1710_en.pdf

I presume you have Windows 7, right? If everything else is ok - printer working properly, you may drag the SmarThru icon form the start menu on your desktop.

Take it in, a blinking check engine light is not a good sign. Solid yellow is ok, blinking yellow or red is in need of service. Get the codes checked asap.

4 beeps & 4 flashes mean problem with the power supply. For my experience, most of the time the PSU is good, it is just overloaded.

For more LED and Beep messages, check this link:

http://bizsupport2.austin.hp.com/bc/docs/support/SupportManual/c00067072/c00067072.pdf