Question about Bush 5693D 24" TV

2 Answers

Bush rf6683vpl after switching tv on by remote or by buttons on tv the picture comes on for a few seconds and then the tv goes into standby mode no picture no sound no nothing is it worth taking for repair

Posted by on

  • kev_goss Feb 14, 2009

    I have the same problem and I know how to solder could you direct me to what i need to solder. 

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

SCRUB THE TV

Posted on Mar 14, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 252 Answers

Yes ,your tv need for repair, but if you know how to solder , try to solder your tv but be careful o short circuit coz it may damage your system.

Posted on Oct 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tv switched itself onto standby and now will not turn back on. tried unplugging it and plugging it back in but it still won't come off standby. when you press the button on the remote it goes green for a...


unit seems to go into protect mode.Theres very little that can be done..There is good chance unit needs to be checked at a repair shop.Try to find one that is authorized for your particular brand if possible

Aug 05, 2009 | Standard (CRT) Televisions

1 Answer

Tv lost picture and sound


TRY UNPLUGING SET FROM THE WALL FOR 1 MINUTE. PLUG SET BACK IN AND CHECK. IF PROBLEM PERSISTS TAKE IT TO A QUALFIED SERVICER. UNIT PROBABLY HAS A DEFECTIVE MAIN TOTAL ASSY.

Jan 12, 2009 | Bush 5693D 24" TV

1 Answer

Standby mode intermittently.


Hello, FixYa

I have normal tv model CNT 2588 code 981, remote control was out of order and I tried to buy a new one from many places in UAE, Suadi Arabia & Egypt but I failed due to it is old model and no spare parts. So I use the tv function through Satel Decoder and use tv main power button for swithing on and off. It seems that caused a problem and tv now could not get power to switch on. Would you e-mail me with the repair manual including the Elect.Circuit to try to repair the problem. Also if you can arrange to send me a new remote control model CNT 2588 code 980. Since the TV Picture and sound are still in an excellant condition, please e-mail me you kind response with the cost if any to send you my Address and money.

Thanks in advanced.

Mohamed Said

Oct 30, 2008 | Standard (CRT) Televisions

2 Answers

Stuck in Standby


change the horizontal output transistor .its busted.

Aug 14, 2008 | Bush 5693D 24" TV

1 Answer

'standby' mode and akb error number


AKB 66 in self diagnostic test means...TV goes to standby (shut-off) for AKB problem 66 times. AKB is White-Balance signal and it is not proper or maintained in your TV. So error signal produced and TV goes to shut-down state.
Regardnig Standby button, its available on remote only. If you push TV Power switch, TV will switch ON, push it again to OFF TV. Power Button on remote set TV in standby status and you dont need to push power button of TV itself.

Aug 14, 2008 | Sony KP-53HS10 TV

1 Answer

Dush TV 28" RF6683VPL switch off while I was waching tv


Hi there sorry but this could any number of things. But i dont think you could repair it your self. It would need to go to a repair shop. It is most likly a power supply fault inside the tv . All the best Bob

Jul 20, 2008 | Bush 5693D 24" TV

1 Answer

Blinking Stand By/Timer LED


You can try this on the remote in standby mode, meaning tv plugged in but set off. Press Display,5,vol+,power on remote.Press each button within a 1 sec interv. Next the CRT display the item being adjusted. Press 1or4 on remote to select item. 3or6 to change the data. Press Muting then Enter to write into memory. Service Reset muting green enter red. Press 8 then enter on remote to initialize. turn set off to exit. wait least 10 sec. before turning back on.

Sep 10, 2007 | Sony KV-32V40 32" TV

1 Answer

Re: Sony KV-24FS120


your problem in system control ic section related to stand by pin check ckt related to stand by section in remote ic check power to system ic loose coniact in remote or system ic thanks

Sep 09, 2007 | Sony FD Trinitron WEGA KV-24FS120 24" TV

1 Answer

TV cut out and stay on standby


hold the power switch in from off for 10 seconds, worked for me.

Jan 06, 2007 | Sony FD Trinitron KV-28FQ75 28" TV

Not finding what you are looking for?
Bush 5693D 24" TV Logo

Related Topics:

255 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bush Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68301 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Are you a Bush Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...