Question about Hotpoint Ultima WF860 Front Load Washer

1 Answer

Hotpoint ultima w860

Hello,
can anyone help us with some advice on our above machine? Its saying F-3 during a cycle and is leaving our washing very wet and it appears to be rinsing when it should be spinning. When F-3 appears there is nothing we can do with the machine and we have to turn it of at mains to re set it.
Any suggestions appreciated.
Julie

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 166 Answers

Peace,
I was going to tell you to reset it, BUT you did and it obiously did not help!
You have an electronic disorder problem and must call service!!!!


Please give me a rating before you sign off here at our web site!

Posted on Sep 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

In my hotpoint ultima WMD942P washing machine's softner compartment i always find water at the end of the cycle. its a new machine.


This is completely normal, the machine puts water into this chamber during the rinse cycle to wash the softener into the machine.

Mar 05, 2012 | Hotpoint Washing Machines

1 Answer

Hotpoint Ultima washing machine: F-01 What does this mean?


The Hotpoint manufacturer's site says this code means:
F01 - Short circuit motor triac - Book a washing machine repair.

However, what it means is that it could have a faulty motor or motor control board. The motor tachometer could also be faulty. Some machines have a little rotating magnet and sensor, and the magnet can become detached. If this code is not constant, and tending to come on during a spin cycle, check the drive belt for wear or slack, and check the motor brushes.

Aug 08, 2011 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Hotpoint washing machine. Replaced drive belt yesterday but fell off again during cycle. Also tightened up pulley. What have I not done?


You most likely didn't tighten up the belt tensioner, this adjusts the tightness of the belt, so as it stretches, during use, this can be, adjusted out.

Apr 07, 2010 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Hotpoint washing machine


f05 is a drainage problem, ther may be something stuck in your pump.
its in the back of the machine in the corner. take the side hose off and unclip the pump from machine and look in to see the propellor may have foriegn object in.

Dec 09, 2008 | Hotpoint Ultima WF860 Front Load Washer

3 Answers

WF860 saying test on the display


Is this machine new and this is the first time you have used it?

If yes - you will need to let it complete the TEST cycle fully before it will be useable. (do not interupt - takes 60 to 90 mins)

Apr 13, 2008 | Hotpoint Ultima WF860 Front Load Washer

2 Answers

Hotpoint Ultima WMA61 loud knocking noise in spin cycle


Hello I think that the drum bearings have gone on the machine..

To open the door and spin the empty drum quickly by hand and you should hear the noise or say a less amplifed one.. Also another way to check is to move the inner durm up and down to see if there is any play in it..

If you need any further advice then dont hesistate to ask....

Jan 14, 2008 | Hotpoint Aquarius WMA52 Front Load Washer

1 Answer

Hotpoint Ultima W860


hi there f10 fault code means pressure switch not sensing,
this could be to do with low water pressure or a bad connection on the pressure switch or control module which is located at the back left hand corner of the machine, remove backplate to gain access and remake all connections on module, if this should not resolve the fault i would be looking to replace the pressure first part no= C00112659 cost about £15

ps. always disconnect from mains before carrying out any work

Oct 20, 2007 | Hotpoint Ultima WF860 Front Load Washer

2 Answers

Noisy spin loose drum


drum bearing need need bearing kit and drum support £60 plus labour at similar price. Appliance Doctor

Feb 02, 2007 | Hotpoint Ultima WF860 Front Load Washer

Not finding what you are looking for?
Hotpoint Ultima WF860 Front Load Washer Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...