Question about Toshiba Portege 3110CT (P000278510) Motherboard

1 Answer

Can i sync a handspring?

Hey i have a handspring visor pro. i broke the bottom pins to sync and even after soudering they dont work. i can send and receive infrared. my laptop sees the infrared. is there an app to sync via pc infrared. Laptop; toshiba 3110ct with win 2000 PDA; Handspring visor pro

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 44 Answers
Re: Can i sync a handspring?

Recent version's of the HOTSYNC app have a provision for IR transfers (older versions may not though). So you should check the HOTSYNC app on the Visor and see if it already has IR transfer abilities. If it does: Use the downarrow to specify the IR transfer on the Visor. Setup HOTSYNC on the computer to accept IR transfers. Line up the ports and tap the HOTSYNC button on the Visor's display. If it doesn't: You may be outta luck. Downloading an updated version of the HOTSYNC app (or some other utility) won't help because you'll need to Sync in order to get the app on the Visor.

Posted on Sep 19, 2005

Add Your Answer

0 characters

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...
3 Points

Related Questions:

1 Answer

I'm upgardeing my ms-7061's cpu from a 1.5 to 2.2


http://www.msi.com/product/mb/KM4M-V.html#/?div=Detail

Download > Manual >

CPU
Supports AMD Athlon / Athlon XP / Duran (Socket 462) processor.
(Socket 462 = Socket A)

Supports from 1100MHz to 3000+ model.

VIA KM266 Pro motherboard chipset - Front Side Bus support of 266MegaHertz.

http://en.wikipedia.org/wiki/List_of_VIA_chipsets#Slot_A_and_Socket_A

(Same specs as a VIA KT266A but with Integrated Graphics.
The 133MHz FSB support shown is doubled. AMD processors are 'Double-pumped')

VIA KM400 motherboard chipset -
FSB support of 266MHz to 333MHz.
(Same as KT400 but with Integrated Graphics)

VIA KM400A motherboard chipset -
FSB support of either 266MHz, 333MHz, or 400MHz
(Same as KT400A but with Integrated Graphics)

Looking at the Bottom/Right corner at the CMOS battery;
There are THREE sets of jumper pins to the bottom right edge of the CMOS battery.

6 pins towards the outside edge of the motherboard, 3 pins to the inside of the motherboard. (Left side of the 6 pins)

On the 6 pins in a row configuration, the top 3 pins is SW1.
The bottom 3 pins is SW2.
The 3 pins to the inside of them is JBAT 1

In the 3 pins for SW1 the bottom pin, or pin closest to the bottom edge of the motherboard, is Pin 1.

Same for SW2. The bottom pin, or pin closest to the bottom edge of the motherboard, is Pin 1.

Jumper on pins;
SW1 pins 2 and 3, SW2 pins 1 and 2 = 266MHz FSB support
SW1 pins 1 and 2, SW2 pins 1 and 2 = 333MHz FSB support

For the KM400A (KT400A) motherboard chipset;
SW1 pins 1 and 2, SW2 pins 2 and 3 = 200MHz FSB support

1) What is the model name, and model number of the AMD processor you are going to use?

2) What kind of Thermal Paste are you using?

3) What are you using to clean the bottom of the Heatsink with, and is the top of the Processor clean?

4) Are you following Anti-Static Precautions?

Post back in a Comment.

Regards,
joecoolvette

Oct 13, 2012 | Motherboards

1 Answer

Where to connect the start switch


For the Abit AB9 pro motherboard?

http://www.newegg.com/Product/Product.aspx?Item=N82E16813127004

A) Motherboard installed in the computer case;
Processor to the Top, Ram Memory slots to the Right, white long PCI slots at the bottom;

The Front Panel header on the motherboard, is at the Bottom/Right corner.

[The plastic front of your computer is the Front Panel.

The area of contact pins on the motherboard, that the main wires from the Front Panel go to, is the Front Panel header ]

The Front Panel header is a plastic rectangular block, with TWO rows of pins.
20 pins. 10 on the Top row; 10 on the Bottom row.

The pins on the Top row are numbered EVEN.
The pins on the Bottom row are numbered ODD.

TOP row; starting at the LEFT side going towards the RIGHT;
Pins 2, 4, 6, 8, No pin 10, No pin 12, No pin 14, 16, No pin, 20.

{4 pins, blank space where 3 pins would be, 1 pin, blank space, 1 pin }

BOTTOM row; starting at the Left side going towards the Right;
Pins 1, 3, 7, and 9. No pin, 13, 15, 17, and 19.

( Top row: 2,4, 6, 8, X, X, X, 16, X, 20
Bottom; ..1, 3, 5, 7, 9, X, 13, 15, 17, 19

X = No pin, or blank spot )

A) Pins 1 and 3 are for the HarDDrive activity LED light.
Pin 1 is for the Positive ( + ) wire.

If the HDD LED is dim when the harddrive is active, and in use, switch the wires around.

B) Pins 5 and 7 are for a Reset switch, IF a Reset switch is used.
(reset button)

C) Pin 9 is N/C. Not connected. (It was for factory use)

D) Pins 13, 15, 17, and 19, are for a Speaker. The small speaker is used so you can hear BIOS Beep Codes. The computers way of telling you something is wrong, and an area to look into for it.

Pin 13 is for the Positive ( + ) wire
Pin 19 is for the Negative ( - ) wire

E) Pins 2 and 4 are for a Suspend Power On LED light.
Pin 2 is for the Positive ( + ) wire.
Ignore.

F) Pins 6 and 8 are for the Power On switch.

G) Pins 16 and 18 are for the Power On LED light.
Pin 16 is for the Positive ( + ) wire.
If the Power On LED light is dim when the computer is on, switch the wires around.

Motherboard manual. It is a PDF file. The computer you are using now has Adobe Reader on it, which uses PDF files.
After you click it may take up to 30 seconds, before the first page comes up.

Page 15.

http://static.tigerdirect.com/pdf/Abit_ab9_series_Manual.pdf

For additional questions please post in a Comment.
Regards,
joecoolvette

Jul 21, 2012 | Abit AB9 Pro Motherboard

1 Answer

Do you have any user manual for front panel usb


http://www.msi.com/product/mb/PM8M-V.html

(MSI PM8M-V H, is version 2.0 )

Hover your mouse cursor on the Download tab.
(Overview / Specification / Download / Support / etc.)

In the drop down list, click on - Manual
Under the subheading - Download, click on the blue -
M7104v1.0.zip

[ This is a Zip file. A Zip file is a file that is compressed, to send easier. The above manual is for the M7104v1.0
It will work for the version 2.0 also.

You need a program to 'Unzip' it. (Decompress)
If WinZip is not working on your computer, go to 7-Zip, and download for free.
If you need guidance in downloading, and unzipping, post back in a Comment ]

There are two USB headers on the motherboard for the Front Panel,
JUSB1 and JUSB2. (Junction USB 1 and Junction USB 2)

Looking along the bottom of the motherboard, FROM the Right going towards the Left;

JFP1 header; (Front Panel main wires)
Header with 4 pins on the Top row, and 5 pins on the Bottom row.

JFP2 header; (Dual color Power On LED, and Speaker)
Header with 4 pins on the Top row, {Speaker}, and 3 pins on the Bottom row.

JUSB2 header.

JUSB1 header.

EACH USB header will support TWO USB ports in the Front Panel.
JUSB1 supports two,
JUSB2 supports two.

For each USB header there are 5 pins across the Top, 4 pins across the Bottom.
The pins are numbered EVEN across the Top, and ODD across the Bottom.

Starting from the LEFT side going across to the RIGHT side;
on the TOP row for JUSB2 and JUSB1;
Pins 2, 4, 6, 8 and 10.

Starting from the LEFT side going across to the RIGHT side;
on the BOTTOM row for JUSB1 and JUSB2;
Pins 1, 3, 5, and 7. There is NO pin 9.

A) Pin 2 is VCC
B) Pin 4 is USB1-
C) Pin 6 is USB1+
D) Pin 8 is Ground

E) Pin 10 is USBOC

Pin 10 is N/C -> Not Connected.
It is there, and Pin 9 is not there, to key which way a connector can go on. Only ONE way.

F) Pin 1 is VCC
G) Pin 3 is USB0-
H) Pin 5 is USB0+
I) Pin 7 is Ground

There is NO pin 9.

(The USB technology used is USB 2.0)

http://pinouts.ru/Slots/USB_pinout.shtml

Let's read together,
Under - USB pinout signals;

"USB is a serial bus. It uses 4 shielded wires: two for power (+5v & GND) and two for differential data signals (labeled as D+ and D- in pinout). NRZI (Non Return to Zero Invert) encoding scheme used to send data with a sync field to synchronise the host, and receiver clocks. In USB data cable Data+ and Data- signals are transmitted on a twisted pair. No termination needed. Half-duplex differential signaling helps to combat the effects of electromagnetic noise on longer lines. Contrary to popular belief, D+ and D- operate together; they are not separate simplex connections."

See the USB examples in the link above, where it labels the contact pins?
The MALE connectors are shown on the Left side.
The FEMALE connectors are shown on the Right side.

Your USB ports will be FEMALE, on the Front Panel.
They are also the A style. USB A style. The Top example to the Right.

Just noting the following in case for some reason, the wires coming from those contact pins in the female USB connector, are not color coded correctly;

Even after you have the wires sorted out, as to which contact pins they go to, DOUBLE-check again. Do NOT just go by the color code of the wires.
Why?

You do NOT want to accidentally connect the +5 Volts (VCC), to the Ground!

Explaining further;
You connect the VCC wire, (Red), of the USB port in the Front Panel, to the Ground pin on the USB header on the motherboard.

(Which means the Ground wire of the USB port, (Black), will probably also be connected to the VCC pin, on the USB header of the motherboard)

Zzzzzzap! There goes your front USB ports. Both USB front panel headers on the motherboard, will be DONE!

Make sure!

Going on;
1) VCC or Vcc, goes back relating to Transistor technology.
Just think of it as the Positive, or power wire.
It is.
It is 5 Volts DC.

2) GND is Ground. It's a DC circuit, and you have a Positive, and a Negative, or Ground.

3) USB1-
That is -> Data-

USB0 is for one USB port in the Front Panel.
USB1 is for another USB port in the Front Panel.

[ Each USB header on the motherboard can be connected, to TWO USB ports on the Front Panel.
Therefore for the two JUSB1 and JUSB2, you can connect Four USB ports in the Front Panel ]

Data- on one USB port in the Front Panel, goes to USB0-

Data- on the other USB port in the Front Panel, goes to USB1-

4) Data+
Same thing.
Data+ on one of the USB ports in the Front Panel, goes to USB0+
Data+ on the other USB port in the Front Panel, goes to USB1+

EACH side of JUSB1 and JUSB2, will support one USB port on the Front Panel.
Two sides per JUSB1 and JUSB2 = 4 USB ports on the Front Panel.

For additional questions, or clarification to anything I have stated above, please post in a Comment.

Regards,
joecoolvette

Jul 20, 2012 | MSI Motherboards

2 Answers

I have an Asus P5QL PRO Motherboard and I'm trying to connect the FP audio and I need some help on how to connect it up properly. On the heaphones lead I have 4 connectors: EAR R EAR L RETURN...


Hi

Pin arrangement for Front panel Audio is usually:

Pin 1 Left MIC-IN Pin 1 right GROUND
Pin 2 Left MIC VVC (or MIC Power, or MIC BIAS) Pin 2 Right empty
Pin 3 Left R EAR (or R OUT) Pin 3 Right R RETURN
Pin 4 Ground or Empty Pin 4 Right empty
Pin 5 Left L EAR (or L OUT) Pin 5 Right L RETURN

This arrangement should apply to both the HD AA/FP or the Standard AC'97 Headers.

I hope this helps

Aug 28, 2011 | ASUS P5QL PRO Motherboard

1 Answer

Hey, i just bought two identical intel D845GRG boards. want to build a couple of machines with 6th, 7th grade computer classes... i am by NO means a hardware guy, but am okay with MoBos, as long as...


Congratulations for your work with the 6th and 7th grades! God bless you! These young ones are the inheritors that will take over after us. I am to see how the human mind is a digital computer, not an analog one. I will need a couple of days to do the set up and we are going to send you lots of information. In the future, please, get in touch with us before you come to an impass. We are here to help you. You will hear from me in a couple of days, more of less... My name is Constantin (arzconst is my internal nickname with Fixya.com). Until then...

Jun 18, 2009 | Intel D845GRG Motherboard

3 Answers

Motherboard Xcel2000 need completed bultin drivers


Hey, this isn't the board for that!  Read the documentation on a search engine and use it to find your Mobo maker's site or the particular driver page.  It isn't broke.....

Sep 10, 2008 | Motherboards

1 Answer

Msi motherboard


@ vinay2412 - YES you need a PSU wil either the 4 or 8 pin molex connector to power the motherboard correctly

the lightscribe drive will not read a DVD or CD until you boot the PC correctly

the wireless k/b will not work until you load the drivers etc. you need a PS2 or USB k/b to get thing going first until the OS is running and you can install drivers

@ shaikh27

your error suggest you need to load drivers from the motherboard driver CD. do you have this?

Jun 19, 2008 | Intel Motherboard

1 Answer

Front panel hook up


HEY MAN U HAVE SERIUS PROBLEM... OK THIS MAY SOLVVE U R PROBLEM....JUST DOWNLOAD U R MOTHERBOARD USERS MANUAL...AL CONNECTIONS ARE GIVEN THERE..EVEN FRONT PANAL SETTINGS TOO.... BEST REGARDS MAIL ADD- SIGMA_SHIVA1@YAHOO.CO.IN

Oct 09, 2007 | Dell (E210882) Motherboard

2 Answers

Viper MSNV-939 ATX Socket 939


I assume you have tried with only one stick of ram individually at a time if you are using two to check it's not the ram as one faulty can cause the system to stop. Also assuming you bought the ram from the same place and is compatible with the board. Sometimes people also forget that the processor in some cases has to be powered by the 4 pin plug from the PSU and not just from the ZIF socket that older processors use to power up, so double check the manual. The other main common cause of the this problem is when you are putting together all the hardware onto the board, if you don't protect it underneath it may have overflexed the board and shorted or damaged the circuitry or the bios chip. That's not to say that the motherboard was'nt faulty in the first place.

Apr 18, 2007 | Mach Speed (S755) Motherboard

Not finding what you are looking for?
Toshiba Portege 3110CT (P000278510) Motherboard Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Brad Brown

Level 3 Expert

13216 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Are you a Toshiba Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...