Question about GE Profile Performance WPSF4170WAA

Open Question

My ge washing machine leaks from the bottom, i did open the front panel and saw the leak coming from the center of the bottom, i did remove all the the other parts to replace the tub seal but, i can't remove the pentagon washer it's very hard i do have the spanner wrench and the adapter but i can't take it out can you suggest me something else to do or what can i do different to take it out. Thank you very much Jose

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
seanpwright
  • 2030 Answers

SOURCE: I am removing a Kenmore washer inner tub with the

No and NO

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/sean_54c3a3dc48a7773c

Posted on Apr 25, 2010

Testimonial: "Thanks"

Ad
  • 1 Answer

SOURCE: GE Front Load Washer

Removing the lower front panel (3 screws nearest floor), and opening the round, white water pump filter cap (be ready to catch about 2 gallons of water!) is the best place to start. All you need is a Phillips head screwdriver and a large, flat pan (deep turkey tray works well)!

YOU WILL NOT BELIEVE what I found in my filter housing this morning (see photo below)!

490ccb1.jpg

The washer is working fine now, although I may go back and remove the entire water pump so it can be dismantled, thoroughly cleaned, and reinstalled.

Posted on Sep 22, 2008

huuum
  • 750 Answers

SOURCE: GE Top load washer.

Hello rschneeweis
Welcome,

Sounds like a seal or drain hose is leaking or the clamp on a hose has vibrated loose.

Water leaking out the bottom of the machine when washing machine begins agitation cycle. If the machine is turned off the water stops leaking even with the tub full of water.

Let me know if you found it and how you do.

Huuum
Please remember to leave a rating

Posted on Oct 04, 2008

  • 670 Answers

SOURCE: water leaks out front center of door during the

Check the door gasket for any damage. A rip or a tear could be the cause of the leak.

Posted on Jul 20, 2010

kevin_getz
  • 1032 Answers

SOURCE: My GE topload washing machine is leaking

Check the hose that connects to the bottom of the tub to the drain hose. Make sure that hose is securely fastened.

Posted on May 30, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer leaks from bottom


you can open the front panel of washer and see if water is coming from the pump located to the right very close to the front of the machine. if the leak is coming from there is an easy fix. you may have a loose drain hose. If the leak is coming from the center of the drum, is a bad news, center chaft seal is bad, if this is the case, it's not worth it to deal with it.

Apr 03, 2014 | GE GTWN4250MWS

1 Answer

Water leaking during wash cycle. How do you get access to inside


I use a putty knife about 2" inward , between the top and the front panel on each side . Give a good hit on one side while slightly pulling the front panel forewafd . Then do the other side . The front panel tilts foreward and hinges on the bottom with tabs . Then lift to remove .

Aug 02, 2010 | GE WBSR3140DW Top Load Washer

2 Answers

Water leaks out front center of door during the


Check the door gasket for any damage. A rip or a tear could be the cause of the leak.

Jul 20, 2010 | GE WSXH208A Front Load Washer

1 Answer

Door leaks at the bottom of my ge profile dishwasher


1 has the machine been pushed into the cupboard hole,this will push the door away from the front of the machine,does it hit the trim around the opening before the closeing?pull out check under are the legs still straight,some you can remove the lower front panel to look under

Dec 02, 2009 | GE Profile PDW8400J Built-in Dishwasher

1 Answer

Wash machine is leaking in the very midle of the bottom


The water pump is probably leaking at the shaft bearing. You need to remove the front panel (or the cabinet if it is formed without a joint at the corners) to see the pump. Once you get the cabinet open it is not difficult to replace the pump.

Nov 24, 2009 | GE Washing Machines

1 Answer

My GE dishwasher is leaking water from the bottom of the machine


first check to make sure door gasket is ok, if bad, replace and test. Make sure to remove bottom front panel during a test and inspect the motor and motor gaskets. It may be leaking here, replace leaking components as needed.

Jul 01, 2009 | GE 24 in. GLD6200L Built-in Dishwasher

1 Answer

Top loading washing machine leaking at center bottom


remove panel below door and run it. Then you can see if it is the front seal or back at pump. Two screws on bottom of panel to remove it

Apr 26, 2009 | Frigidaire ATF6000ES Front Load Washer

4 Answers

GE Front Load Washer


Removing the lower front panel (3 screws nearest floor), and opening the round, white water pump filter cap (be ready to catch about 2 gallons of water!) is the best place to start. All you need is a Phillips head screwdriver and a large, flat pan (deep turkey tray works well)!

YOU WILL NOT BELIEVE what I found in my filter housing this morning (see photo below)!

490ccb1.jpg

The washer is working fine now, although I may go back and remove the entire water pump so it can be dismantled, thoroughly cleaned, and reinstalled.

Mar 16, 2008 | GE WSXH208A Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

geapptech

Level 2 Expert

157 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...