- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Check the remote control for its infrared emission. Without remote control, you can't set it out of standby. If you wish to get more details, check this site. Pull up
older posts there. Check the site with
patience, as it has over 2350 posts now.
All are related to electronic equipment repair help. There is one post have details about how to check and repair remote controls. http://electronicshelponline.blogspot.com/
I had this same problem with my Mitsubishi it is when you have fast on mode set it pre warms the bulb to much. I turneed it off and now the bulb has lasted much longer
Setting the Power-On Mode feature
You can select either Power-Saving or Fast mode.
If you select Power-Saving mode and you turn off the TV, it
can take several seconds for the picture to appear when you turn
on the TV again. Power-Saving mode saves more power than
Fast mode. See "Specifications" on page 66 for details.
If you select Fast mode and the TV is turned off, the TV will
stay in Standby mode for several minutes (see Note below). If
the TV is turned on from Standby mode, the full picture
To set the Power-On Mode feature:
1 Press Y and open the Setup menu.
2 Highlight Power-On Mode and press c.
3 Press b or B to select either Fast or Power-Saving and
Note: If Power-On Mode is set to Fast and you turn off the TV,
the following will occur for a few minutes:
• The screen (lamp) lights dimly; and
• The fans continue to run.
This is a function of the Power-On Fast Shutdown mode and is
not a TV malfunction. If you do not prefer this, set the PowerOn Mode feature to Power-Saving.
When the Power-On Mode feature is set to Power-Saving, if
you repeatedly turn the TV on and off in a short period of time,
the useful service life of the lamp may be shorter than the
average useful service life (- page 63).
this is from your manual not my Mitsubishi
please rate this answer if you felt it was useful.
If connected to cable or satellite your tv will work after digital conversion occurs. If using an antenna, look up a local TV station to see if they're already broadcasting in digital. Most are. Enter that DIGITAL channel # using your remote. If you get a picture, you don't need a converter box.
It seems like there's a problem with a component on the Power Supply of your TV or there's a problem with your Picture Tube. I don't recommend you working on TV's unless you know what you're doing since you can get badly shocked if you don't discharge the Ulter Cap on the Picture Tube. If you don't know what you're doing then I suggest you get it repaired by someone who knows what they're doing.
I believe you either have a problem with your Power Supply inside your TV from a defective component in the circuit or you have a problem with the Picture Tube on your TV. I don't recommend you working on TV's by yourself unless you know what you're doing since you can get badly shocked. You need to discharge the Picture Tube on the TV before you work down any further. If you don't know what you're doing then you should get someone that knows what they're doing to work on your TV.
i got akai 29" tv before 1 1/2 yrs back.3days back it was burnt with a huge sound. the set was burnt with a high smoke.since 1 wk i am waiting for your service agent.when they will come?this problem was not present in sony,LG,or other tv.akai is this much weak set.there was no lightnening only rain was present at that time.i hope you will change the set with free of cost. K.P.Varghese,Plot.330/54,St-3E(East),Pragati Nagar,Risali,Bhilai,Durg(C>G)Pin-490006 Phone:0788 2271393,Mob:9424124176.