Question about Konica Minolta DiMAGE A2 Digital Camera

1 Answer

What is the rate of continuous advance? - Konica Minolta DiMAGE A2 Digital Camera

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 425 Answers

The speed is selectable from 3 types at the continuous advance. Continuous advance: Single shot AF: max. 1.8 fps (live view and anti-shake are activated for each frame. TIFF image cannot be taken), continuous AF: max. 1.9 fps (live view, AF, AE, anti-shake are activated for each frame. TIFF image cannot be taken.) Hi-Speed continuous advance: max. 2.7 fps (Anti-shake is activated for each frame. AF, AE, WB, and live view are fixed at the first frame. TIFF image cannot be taken.) UHS continuous advance: 7 fps. (Image size is fixed at 640x480. AF, AE, and WB are fixed at the first frame. TIFF and RAW image cannot be taken. Digital zoom disabled.) Actual speed may vary depending on the subjects and shooting conditions. * Three frames can be taken continuously in normal and Hi continuous mode. *In UHS mode, the images can be taken as much as possible to the limitation of the storage capacity. For reference, STD: 180 frames, FINE: 160 frames, X. FINE: 100 frames (approx.).

Posted on Sep 15, 2005

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What Reasons Limiting Casting Mold to Develop in China?


First, although importance of casting mold foundry is recognized by more and more people, recognition has not reached to due height yet. So, status of mold is still not clear and policies cannot be implemented completely. Received supporting strength and intensity are insufficient. Besides insiders, only a few people know about features of mold industry. To get more supports, publicity is still priority. Second, compared with international advanced level, Chinese casting mold industry is still backward on idea, design, craft, technology and experience. In general, China is still learning from advanced countries, lacking of innovation. Information manufacturing and management, innovation are not realized. China is equivalent to intermediate level. Compared with advanced level, the whole industry level is backward by about 15 years. Among that, online test and information management of casting mold are backward by more than 15 years. Reducing gap has a long way to go forward.Third, the high economic growth rate is almost ended. In the future, Chinese economy will show the trend of intermediate speed. Cost inflation and rate of profit declining will become normal and constraining force of energy and ecological environment will be larger and larger. Structural adjustment and transformation of growth pattern are urgent. There are a lot of factors around the world. Under such situation, castings mold industry has difficulty for maintaining higher growth rate and sustainable development while the objective must be realized.Forth, phenomena of financing difficulty, accounts due growing, financial strain, cost growing and rate of profit constantly decreasing still exist in small enterprises and those problems are not figured out, still growing continuously. Partial provinces or cities in south have energy supply tension. Situation that commercial power is limited also exists. Fifth, talent is in shortage. In particular, shortage of senior talent has become a key bottle neck for mold industry. Although China has made a great progress in talent cultivation, it is still far away from meeting requirements. Demographic dividend in China is continuously reducing and human resource will be tightened for a long time. Enhancing talent cultivation to meet demand, using high technologies, developing informatization, standardization and automation to reduce manpower are priorities.

Jan 05, 2017 | Cars & Trucks

4 Answers

Codes p0011 and p0021


P0011 "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)
P0021 "A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

Oct 10, 2011 | 2004 Ford F150

1 Answer

Hi, I recently purchased a used makita 6100r generator and when checking it out I discovered on my 30 amp 220 receptacles arent getting full power. I took out the receptacle and checked the wires in back...


You may be asking too much of the unit; the 5800 watts a which it is spec'd, may be a 'peak' power rating which may be 15-20% higher than its continuous rating. 30 Amps at 220 volts implies 6600 watts which is higher than even the peak power rating. I would expect the unit to produce ~4800 watts continuous or around 22 Amps.
Decided to check my statements and found this, which I quote:
Generator Volts AC (60Hz) 120/240 Max. Output Current 5800W-48.3A/24.2A Rated Output Current 4800W-40A/20A Volts DC (AMPS) 12 (8.3)

Aug 28, 2011 | Makita G6100R 5800 Watt Generator

1 Answer

My maytag neptune dryer is taking twice as long to dry cloths. i've had it 5 years & it's gas.


Clogged Vent
If your dryer seems to run forever, it could be because of a clogged vent or internal ductwork. Your dryer may have an automatic cycle that turns off the dryer when the clothes are dry. It does this with a special thermostat or moisture-sensing system.
Normally, this is what happens during an automatic cycle:
The thermostat tells the dryer to heat until the interior of the dryer reaches a pre-set temperature--say 135 degrees.
When the dryer reaches the pre-set temperature, the thermostat tells the timer to begin advancing. (If there's a moisture sensor, the timer advances only if the moisture content of the clothing is low enough.)
The timer advances until the interior cools, then the thermostat tells the timer to stop advancing, and tells the dryer to start heating again.
This cycle continues until the clothes are dry. But...if the vent is clogged, the dryer may never reach the proper operating temperature, so it doesn't send the signal to the timer and the dryer continues to run indefinitely, even if the clothes are completely dry. To fix the problem, clean the vent and/or internal ductwork.
Cycling thermostat
Although this isn't a common problem, one of the thermostats that controls the temperature in your dryer may break and cause the dryer to heat poorly. If so, you need to replace it. The thermostat is usually a small, round, black device mounted to an oblong steel plate. The plate is mounted to the internal ductwork . This thermostat usually has four wires going to it. Check the 2 terminals that are opposite each other and are the closer together of the 2. These 2 terminals should have continuity. If not replace the thermostat.
This is a free answer, Please rate me.

Oct 05, 2010 | Maytag Neptune MDG5500AW Gas Dryer

1 Answer

MY KENMORE DRYER IS TUMBLEING BUT IT WONT DRY M CLOTHS


Clogged Vent
If your dryer seems to run forever, it could be because of a clogged vent or internal ductwork. Your dryer may have an automatic cycle that turns off the dryer when the clothes are dry. It does this with a special thermostat or moisture-sensing system.
Normally, this is what happens during an automatic cycle:
The thermostat tells the dryer to heat until the interior of the dryer reaches a pre-set temperature--say 135 degrees.
When the dryer reaches the pre-set temperature, the thermostat tells the timer to begin advancing. (If there's a moisture sensor, the timer advances only if the moisture content of the clothing is low enough.)
The timer advances until the interior cools, then the thermostat tells the timer to stop advancing, and tells the dryer to start heating again.
This cycle continues until the clothes are dry. But...if the vent is clogged, the dryer may never reach the proper operating temperature, so it doesn't send the signal to the timer and the dryer continues to run indefinitely, even if the clothes are completely dry. To fix the problem, clean the vent and/or internal ductwork.
.
Cycling thermostat
Although this isn't a common problem, one of the thermostats that controls the temperature in your dryer may break and cause the dryer to heat poorly. If so, you need to replace it. The thermostat is usually a small, round, black device mounted to an oblong steel plate. The plate is mounted to the internal ductwork . This thermostat usually has four wires going to it. Check the 2 terminals that are opposite each other and are the closer together of the 2. These 2 terminals should have continuity. If not replace the thermostat.
This is a free answer, Please rate me

Oct 04, 2010 | Kenmore 73952 Gas Dryer

1 Answer

Number lock


the problem is may be accidentally water would have entered into the keypad.. one by one this problem will continue to many keys.. so better change the keypad by giving to local service station... hope i have helped you.. dont forget to rate me.. thank you in advance...

May 01, 2008 | Motorola Mobility RAZR V3i Cellular Phone

1 Answer

Washer stops suddenly and water isn't drained out


Hi tieuvodanh; Sounds like the timer has gone out. If you can advance the selector dial manualy, and the machine continues to operate as it should, then this is the problem. Replacing the timer will require some advanced knowledge of washers and the ability to use a box of hand tools. A good handy man will be able to repair this for you. Best regards; HELP2DIY Please don't forget to rate my answer.

Jul 10, 2007 | Kenmore 22422 Top Load Washer

1 Answer

What is the rate of continuous frame advance?


The continuous advance speed is approximately 2 fps (frame per second), but actual speed may vary depending on the subject or according to the selected image size. The maximum number of images that the camera can capture continuously is as below. Fine: 5/8/11/23 Std: 7/11/16/32 Econ: 11/17/22/40 Super Fine, RAW: Not available (Image size: 2560x1920 / 1600x1200 / 1280x960 / 640x480) On the other hand, the UHS (Ultra High Speed) achieves up to 7fps continuous capturing. The maximum number of images that the camera can capture continuously is as below. Fine: 15 Std: 31 Econ: 39 - Image Size is 1280x960 (SXGA) only. - AF, AE and White Balance are locked for the first frame in the series. - 1/8s or faster shutter speed is automatically selected. - Digital subject program is unavailable.

Sep 15, 2005 | Konica Minolta DiMAGE 7i Digital Camera

1 Answer

Is the focus fixed at the first frame in the continuous advance mode?


If the focus mode is set to continuous AF, AF is activated for every frame in the continuous advance mode (including the progressive capture). However, it is fixed at the first frame in the UHS continuous advance mode (including the progressive capture UHS continuous advance).

Sep 13, 2005 | Konica Minolta DiMAGE Z3 Digital Camera

Not finding what you are looking for?
Konica Minolta DiMAGE A2 Digital Camera Logo

Related Topics:

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Cameras Experts

Steven Wander
Steven Wander

Level 3 Expert

593 Answers

Computer Links

Level 3 Expert

2386 Answers

comment
comment

Level 2 Expert

78 Answers

Are you a Konica Minolta Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...