Question about Audio & Video Receivers

1 Answer

I am not reciveing two channels that I normally recieve on my Opticum 7010A Digital Sateelite receiver.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 141 Answers

1) Problem with LNB
2) problem with cable
3) problem with receiver

It's hard to check the LNB unless you have a spare one, but you could switch the cables and see if the reciever reports a switch in the good channel to the other side. This should tell you where the problem is.

Of course, it could be a carrier problem, but this is not likely, especially if it continues for a long period of time.

Posted on Sep 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenwood vr606 reciever shutting off subwoofer and centre speaker simultaneously after few minutes/seconds of powering on. WHat's the cause?


The receiver's out put sections are grouped in pairs. Front left and right in one output, rear left and right in second output, and center channel and sub output on the third. Sounds like a semiconductor or semiconductors have gone bad in the center & sub output.

Nov 19, 2015 | Kenwood VR-606 Receiver

1 Answer

Opticum xc80 digital cable receiver


Try contacting Opticum for a manual

Apr 20, 2013 | Audio & Video Receivers

1 Answer

When watching cable tv we are not getting any sound from the speakers. We do get sound from all the speakers when watching a dvd or listen to the stereo. I have a Yamaha HTR 5660 receiver. All the cables...


Your best bet is to hook all your video components directly to TV, using your TV's menu to choose what you want to watch, and then hooking reciever to TV via digital optical out from TV to digital optical in on reciever. From what I read, your reciever has 6 digital optical inputs. Anyway, try running, at least, your cable box to TV, best by HDMI, the run digital optical out to reciever. Make sure you go throught he recievers menu to make sure you have he right channel selected for audio.

Jun 25, 2011 | Yamaha HTR-5660 Receiver

1 Answer

Sherwood 6500 reciver


check your speaker wires make sure they are not shorting against each other down the line, that will cause the reciever to go into standby.

Jan 25, 2009 | Insignia 200W Stereo Receiver

1 Answer

No Audio when I play Blu-Ray discs with Dolby TrueHD


For dolby digital to work you have to have the optical or coax cable hooked up to the reciever ,The HDMI cable is for digital video and audio output but does not support dolby digital out the cable into your reciever , so just turn off the dolby digital on your reciever and you should hear the sound.
here is more info

Dolby TrueHD is an advanced lossless multi-channel audio codec developed by Dolby Laboratories which is intended primarily for high-definition home-entertainment equipment such as Blu-ray Disc. It is the successor to the AC-3 Dolby Digital surround sound codec which was used as the audio standard for DVD discs. In this application, Dolby TrueHD competes with DTS-HD Master Audio, another lossless codec from Digital Theater System.
Dolby TrueHD uses Meridian Lossless Packing (MLP) as its mathematical basis for compressing audio samples. MLP was used on the earlier DVD-Audio format, but details of TrueHD and DVD-Audio differ substantially. A Dolby TrueHD bitstream can carry up to 14 discrete sound channels. Sample depths up to 24 bits/sample and audio sample rates up to 192 kHz are supported. Like the more common legacy codec Dolby Digital, TrueHD bitstreams carry program metadata. Metadata is separate from the coding format and compressed audio samples, but stores relevant information about the audio waveform. For example, dialog normalization and Dynamic range compression are controlled by metadata embedded in the TrueHD bitstream.

May 19, 2008 | Marantz SR-7200 Receiver

1 Answer

Reciever get louder in one channel then static then goes back to normal


HAI,IT'S A SMALL PROBLEM ANY DRY SOLD INLEFT AUDIO SECTION

Apr 30, 2008 | Nakamichi AV-10 Receiver

2 Answers

XBOX 360 to JVC RX 5060b


does your reciver have video ins and outs monitor out u have to send master video out from jvc to tv 1st u know im open for chat

Jan 06, 2008 | Audio & Video Receivers

2 Answers

No sound


I had the same problem, unplugged the receiver for 5 minutes, then when I plugged it back in, it worked.

Jan 05, 2008 | Harman Multimedia AVR 235 7.1 Channels...

2 Answers

Pioneer vsx d512


All you have to do is connect the coaxial out from pc to any audio i/p at the back of vsx d512.but ensure you select the right channel to play the audio ( eg. tape i/p select tape at front control, aux i/p select the aux at front control )

Aug 03, 2007 | Pioneer VSX-D511 Receiver

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68368 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...