Question about Pioneer SD-533HD5 53" Rear Projection HDTV

1 Answer

Pioneer TV problem

Hello, I have the same problem with my TV you had a while back.

I saw your pics of the TV on esnip.com, they were very helpful, I am going to change the IC for the convergence problem, will that also fix the slight curve on the left hand side that I see sometimes on the screen.

Also, how did you get the board out of the TV, on which the IC needs to be changed?

Will appreciate your response.

Thanks
AJ

akanodia98@yahoo.com

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 136 Answers

Http://home.earthlink.net/~oleg.filippov/ConvergenceFix.htm

check out for this link above to do it your self.

thanks.

Posted on Oct 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a Pioneer pro elite 730hdi. When you try to turn it on (main power, not standby), the tv cycles from the red (standby) light with the normal click to the green light, then one second later, it cycles...


Hello,

Your power supply board is dead, u know basic electronics' and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get your TV power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.

Hoping this will help in solving the problem....

Aug 09, 2011 | Pioneer PRO-730HDi 64 in. Rear Projection...

1 Answer

I have a 64 inch hdtv pioneer projection monitor sd-643hd5 and it won't fit into my basement. What can I do? Thank You In Advance, Bruce Morash


Ha Ha, I had the exact problem. I think mine is the same model of TV as well, I have a 64" Pioneer made in 2003. So my TV would hit the slanted ceiling above my stairs as I tried to move it down. I first took off the wheels of the TV and this helped but it was not quite enough. So since the bottom of the TV is flat with exception of the side boards and the front trim. I removed the front trim temporarily and cut off the side boards with a circular saw till even with the flat bottom. This gave me 2.5" more clearance which was enough to fit the TV downstairs. Hint if you scribe the cut line with a utility knife it will reduce chipping.
TimBilt

Mar 28, 2011 | Pioneer SD-643HD5 64" Rear Projection...

1 Answer

Pioneer 5065 tv


hello,
Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;}
Power supply board have problems,just not dead yet.Replaced the power supply board,will solved this problems.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement. Good luck


May 25, 2010 | Pioneer SD-P50A5-K 50" Rear Projection...

1 Answer

When switching on...clicks, but no pic and red light flashing... must reset by switching powerswitch off than on..this went on sporadically for 4yrs..now samething happend accompanied by a loud pop and now...


Hi Pepe.

Only when there is no power at all, no led on, and no sign of life whatsoever, that means that the problem is likely the internal power supply board.


If instead the TV stays in stand-by, with the LED light on and flashing, but does not respond to remote, or to the buttons on the chassis, then the TV is in protect (safe) mode because an internal fault had been detected. In this case the fault is not necessary the PSU. Parts must be tested to find out. The clicking sound is the protection circuit that keeps turning off the PSU to prevent further damage.

If the problem is the PSU, often it is possible to see at a glance that one of the big electrolytic capacitors in PSU board has blown.

General troubleshooting on this article: Why my TV does not start up and remains in... . I do not think it will help in your case.


If that does not work, contact the manufacturer at the number listed on the owners manual to get the TV repaired by a licensed technician.
Pioneer covers the PSU or other parts even out of warranty only when a determined factory defect concerning that model and year had been reported by a number of technicians.
To find the contact see:
USA:Pioneer Electronics
Contact us - Pioneer Europe
Pioneer Electronics Asiacenter
Contact Us - Pioneer UK
contact us - Welcome to the pioneer global media Website

Regards.

Feb 18, 2010 | Televison & Video

1 Answer

Just got a pioneer elite pro 119 from a buddy of


If you don't mind opening the thing, open it up and follow the power lead inside the TV. Somewhere along the line should be a fuse. I'd start there.

Oct 06, 2009 | Pioneer PRO-119 60" Rear Projection...

1 Answer

Tv with no pic no sound on and off work


Hello mackenzie212, The loud pop you heard was most likely a capacitor exploding. I beleve the capacitor is also located in the power supply section of your TV. If you take the back off of the set you will see what can be described as a exploded, or bloated can. This component can be replaced, but I advise you to have it done by a qualified TV technician. This is due to the fact that their may be other unknown factors as to why the capacitor exploded, and a qualified TV technician can determine these causes past the obvious changing of the defective component. I hope this helps, Thank you, Shuttle83 http://www.electron-age-technologies-llc.com

Jun 14, 2009 | Hitachi 51F59 51" HDTV Projection...

1 Answer

Pioneer SD-p5073-K Shuts off


it is the power supply board an know problem with pioneer. If you have any soldering experience you can remove the powersupply board and resolder the tracks and as many parts as you can. I had the same problem and not the power supply works great. You will soon have other problems like pic and sound going intermittant where you have to hit the tv to get it back on. more solder problems on video main board. best of luck

Aug 22, 2008 | Pioneer SD-P50A5-K 50" Rear Projection...

1 Answer

Help


HELLO ok the first thing to do is unplug the set.!!!!#2 then take off the back of the set.!!! #3 then look for the fuse holder's there will be 3 to 4 of them. and check them to see if there good.!!! # 4 ok if all the fuse's are good .then it still could be a couple of thing's a clod solder joint.!!! or dry socket.!!! or a bad fly back transformer.!!! & horz.out put transtior.!! are bad and need to be replaced. well hope this help's you "GOOD LUCK"

Aug 11, 2008 | Pioneer SD-533HD5 53" Rear Projection HDTV

2 Answers

SD533HD% Rear Projection TV wont turn on


You may need the power supply board resoldered as I had the same problem. The guy listed below can do it for you as I shipped mine from Illinois to him in California... Piece of cake getting the board out of the back and it's not too fraigile... Just pack in bubble wrap and it will be fine. My TV is now working great.

BUT DON'T DELAY AS SOONER LATER TV WILL NOT RESTART..


http://www.avsforum.com/avs-vb/showthread.php?t=402397&pp=30&page=38

Good luck.



cell

Dec 28, 2007 | Pioneer SD-533HD5 53" Rear Projection HDTV

1 Answer

CUT OFF TO STANBY


See Speargunner Oct.26,2007.................................T.

Jan 08, 2007 | Pioneer PRO-99 TV

Not finding what you are looking for?
Pioneer SD-533HD5 53" Rear Projection HDTV Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69708 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6364 Answers

Are you a Pioneer Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...