Question about Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher

1 Answer

Main control panel

I have no leds on the frount of the panel. When i switch on the machine all i get in the screen is 188 a snow flake top right of this and an 's' shape top left. Cant reset it holding down the right buttons. Any ideas anyone, is it time to replace it.

thanks

dennis

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 750 Answers

Hello Dennis,
Welcome

You said, You have no leds on the front of the panel. When i switch on the machine all i get in the screen is 188 a snow flake top right of this and an 's' shape top left. Cant reset it holding down the right buttons. Any ideas anyone, is it time to replace it. thanks Dennis

I need the model number and year!
Waiting your response!

Huuum

Posted on Oct 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Kleenmaid DW3 dishwasher not running.


HI,

If there's no water entering your dishwasher, check these:

Water-inlet valve
Float switch
Water-inlet valve The water-inlet valve lets water enter the machine. If this valve is defective, you need to completely replace it. It's usually located behind the lower access panel on the left or right side. It's the device with the main water line (usually copper) from the house, a rubber tube to the dishwasher, and two wires attached to it.

Float switch The float switch is a small electrical switch that's located right below the dishwasher "floor." Above the switch, on the inside of the dishwasher, is a plastic cylinder that floats up as water fills the dishwasher. If this switch is defective, or if the plastic float gets caught or trapped in the raised position, the water can't enter the dishwasher. If the float switch is defective, you need to replace it.

Sep 12, 2008 | Dishwashers

1 Answer

Where is filler sylonoid for hobart lx30h dish washer


The fill solenoid is behind the lower panel, attached to the left side of the booster tank. There is a screen in the end of the fill hose that may be clogged. You require 20 psi flow rate to run the machine properly.
Pull the top tray out, place a magnet on the door switch, with the door closed and monitor the 3 led lights on the control board while its filling. All 3 should light up. Use caution around the high voltages present on the relay board and the booster contactor.
The probes in the right rear corner of the tank send the water level signals to the control board. The tips must be clean of scale or debris that may signal that water is present, when it is not.

May 28, 2014 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Snowflake symbol light is on


It might be showing that the rinse aid level is low. Top it up and see if the snow flake light turns off.

Apr 20, 2014 | Dishwashers

1 Answer

Error code 30 is showing on our zanussi ZDF 511 dishwasher, this is Anti Flood warning what could be casuing this, lack of water to machine maybe ?. thanks


This is pretty complex machine and you would need to have and be able to use a multimeter to check some of the components. The error code retrieved is shown in the service manual as follows. Inconsistency between level on electronic pressure switch and level on anti-boiling pressure switch 2 Possible Causes are ; Pressure switch defective; Electrical current leak between heating element and ground; Heating element; Wiring defective; Main board defective. Unplug the appliance and take the top off. Locate the pressure switches, circular items with thin tube attached to each. Take the thin tubes off, block one with your thumb and blow as hard and as long as you can down the other. Refit the tubes and try the machine again. If still faulty, ensure the wiring to the switches and the main control board is good. If still faulty, you'll need to take the rear panel off and check the heater. If still faulty, it's time to begin replacing parts, first the pressure switches and if still not working the main control board Read more: http://www.justanswer.com/questions/2o419-zanussi-zwf-1431w-washing-machine-error-30-being-displayed#ixzz0h0FQPFHS

Mar 02, 2010 | Dishwashers

1 Answer

Machine is beeping and a faucet is appearing in the panel


I just fixed this fault on my SHE68m05uc. The fault lets the machine run through any cycle and every ting else was working properly. In line between the fill valve and fill float assembly there is an electro magnetic impeller which is "open" if there is no water flow. the signal goes to the timer control board on the lower right side of the machine. If you Pull the impeller, take an OHM reading across the sensor that is mounted to the side of the impeller and blow into one end. If the measurement changes as it rotates, its good. if its shorted "0 Ohms" its broke. The part was about 17$

Nov 20, 2008 | Bosch Evolution 800 SHE68M05UC Stainless...

2 Answers

My maytag dishwasher appears dead just after 1 year


You probably have a bad main control or console control unit in there. Turn power off to the machine, be sure that BOTH of your door switches are ok. Unplug your membrane to control panel ribbon cable, then put everything back in place. Leave the door open, then turn power back on to machine. (also, be sure the thermal fuse hasnt tripped while your in the console). After re-appling power, close the door, and wait a few, if the console unit is bad, the machine will go into drain mode (you will here the unit start in drain). If no drain mode, then your control is shorted. You dont have to see any burn marks, etc for one to be bad, in fact, 98% of the boards we replace, dont show any signs of problems. Let me know what you find out.

Nov 15, 2008 | Maytag 24 in. MDB5600A Jetclean II...

2 Answers

Whirlpool ADP951 modulogic - not working


try holding down the on button for three seconds and sometimes it will complete the cycle. ours doesn't start the whole time. check your water regulator valve under your sink, as it may be leaking which may cause the problem, in the process of replacing mine, but can't find the psi value

Apr 14, 2008 | Dishwashers

Not finding what you are looking for?
Siemens 24 in. SE25A266 ExtraKlasse Free-standing Dishwasher Logo

Related Topics:

478 people viewed this question

Ask a Question

Usually answered in minutes!

Top Siemens Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

valuesrespec

Level 2 Expert

89 Answers

pro appl ser

Level 2 Expert

75 Answers

Are you a Siemens Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...